Sharp AN-PH7LP1 Installation Manual

INSTALLATION MANUAL
CAUTION:
• Potential hazard of glass particles if lamp ruptures. Please have a Sharp Authorized Projector Dealer or
Service Center* replace lamp if rupture occurs.
• Do not remove the lamp unit directly after operation of the projector. The lamp may be extremely hot. Wait at
least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before
removing the lamp unit.
■ It is recommended that the lamp be replaced when the remaining lamp life becomes 5% or less, or when you notice a signifi-
cant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this
projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized Projector
Dealer or Service Center*. For the name of the nearest Sharp Authorized Projector Dealer or Service Center*,
please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information
www.lamprecycle.org or 1-800-BE-SHARP
* Confirm the name of the Dealer or Service Center referring to your projector operation manual.
Removing and Installing the
Lamp Unit
Info
• Ensure the lamp unit is removed using the handle.
Ensure the glass surface of the lamp unit or the
inside of the projector are not touched.
• To avoid injury to yourself and damage to the lamp,
be sure to carefully follow the steps below.
• Do not loosen other screws except for the lamp unit
cover and lamp unit.
(Only the silver screws are loosened.)
1
Press on the projector or
on the remote control to put the pro-
jector into standby mode.
• Wait until the cooling fan stops.
Warning!
• Do not remove the lamp unit from the projector
right after use. The lamp and parts around the
lamp will be very hot and may cause burn or
injury.
2
Disconnect the power cord.
• Unplug the power cord from the AC socket.
• Leave the lamp until it has fully cooled down
(about 1 hour).
3
Remove the lamp unit cover.
• Loosen the user service screw (1) that se-
cures the lamp unit cover. Remove the lamp
unit cover (2).
∫
∫
∫
∫
∫
∫
∫
∫
∫
∫
∫
∫
1
2
LAMP UNIT (LAMP/CAGE MODULE)
FOR PROJECTOR
AN-PH7LP1/AN-PH7LP2
Model
U.S.A. ONLY
Power cord
2
1
User service
screw
2
1
4
Remove the lamp unit.
• Loosen the securing screws (two for each lamp)
from the lamp unit. Hold the lamp unit by the
handle and pull it in the direction of the arrow.
At this time, keep the lamp unit horizontal and
do not tilt it.
5
Insert the new lamp unit.
• Press the lamp unit firmly into the lamp unit
compartment. Fasten the securing screws.
• Be sure that AN-PH7LP1 and AN-PH7LP2 are
respective type.
6
Replace the lamp unit cover.
• Align the lamp unit cover and slide it to close.
Then tighten the user service screw to secure
the lamp unit cover.
Info
• If the lamp unit and lamp unit cover are not cor-
rectly installed, the power will not turn on, even if
the power cord is connected to the projector.
STANDBY
button
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
• Make sure to reset the lamp timer only when re-
placing the lamp. If you reset the lamp timer and
continue to use the same lamp, this may cause the
lamp to become damaged or explode.
1
Connect the power cord.
• Plug the power cord into the AC socket of the projector.
2
Reset the lamp timer.
For Lamp 1
• When you reset the timer for AN-PH7LP1, while
simultaneously holding down
press on the projector.
• "LAMP 1 100%" is displayed, indicating that the
lamp timer is reset.
For Lamp 2
• When you reset the timer for AN-PH7LP2, while
simultaneously holding down
press on the projector.
• "LAMP 2 100%" is displayed, indicating that the
lamp timer is reset.
∫
∫
∫
∫
∫
∫
∫
∫
∫
∫
∫
Securing screws
AN-PH7LP1
AN-PH7LP2
For Lamp 1 For Lamp 2
Compartment for Compartment for
AN-PH7LP1
AN-PH7LP2
To AC socket
ON button
and ,
H&V LENS
SHIFT
button
and ,
Handle
User service
screw
Power cord
ENTER button
MENU button
Printed in China
9NK5010058300
06P12-CH-NM
Printed in China
9NK5010058300
06P12-CH-NM