Sealey SCK15.V3 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
Store in a dry easily accessible area.
9
IMPORTANT: Make sure the kit is in a known location.
WARNING! Find out the nature of the spilled substance, it may help to deal with it more
‰
effectively.
IMPORTANT: Try to locate the source and stem the flow, put a drip tray or bucket in place.
Be aware of the safety requirements (C.O.S.H.H.) for all stored fluids in your workshop.
9
Wear safety equipment as advised in (C.O.S.H.H.) statements when using fluid or cleaning
9
up after a spillage.
Evacuate the area and notify anyone nearby, then get help immediately.
9
Seal off area with a barrier, tape or a sign.
9
Check that no-one is injured, seek medical advice.
9
Mark in permanent felt tip pen the fluid contained in the "HAZARDOUS WASTE ONLY" bag.
9
Dispose of hazardous waste immediately and responsibly.
9
DO NOT use any single item in the kit more than once.
8
DO NOT use the kit for any purpose other than for which it is designed.
8
DO NOT use whilst eating, drinking, smoking; under the influence of drugs, alcohol, intoxicating medication, or if fatigued.
8
2. INTRODUCTION
Designed to absorb spills and drips with a maximum capacity of 15L. Contains a range of high quality absorbents, including high-
grade polypropylene pads that can absorb up to 1L of fluid and featuring a double weight cover stock for maximum absorbency.
Supplied with 1.2m absorbent sock specially designed to absorb up to 5L of fluid and create barriers to keep spills from spreading.
Suitable for use with oil, petrol, diesel, coolants, mild solvents, water and other spills. Full list of absorbent applications provided in
each kit. Supplied in a resealable storage bag.
3. SPECIFICATION
Model No:
Capacity:
Contents:
Sizes:
4. OPERATION
4.1. Shallow spills and final absorption of a spill should be carriedout using pads,
but only once containment is complete. The pads should be left in contact with the
fluid for about two or three minutes, or until saturated. Each pad will contain up to
one litre of fluid approximately, depending upon viscosity.
4.2. When using the absorbent sock, it should be used to form a temporary dam to
contain fluid and not as a mop. A nominal 300mm overlap of ends to contain fluid
is suggested. (Smaller spills would require the SCK15 kit, medium spills SCK30 kit
and larger spills SCK50 kit). All sold Separately.
4.3. Included in the kit is a large clearly marked disposal bag and associated tie. All
used absorbent's should be packed in the disposal bag and the contents indelibly
marked in the spaces marked "PRODUCT" and "CATEGORY".
4.4. Dispose of immediately, following all local environmental guidelines.
© Jack Sealey Limited
SPILL CONTROL KITS (15LTR, 30LTR OR 50LTR)
MODEL NO:
Wear protective Wear safety
gloves footwear
SCK15.V3
15L
Pad (x10), Sock, Disposal Bag with
Ties (x1)
Pad - 500 x 400mm, Sock - 80mm x
1.2mm
Original Language Version
SCK15.V3, SCK30.V3 or SCK50.V3
Wear protective Wear a mask
clothing
SCK30.V3
30L
Pad (x15), Sock (x3), Disposal Bag
with Ties (x1)
Pad - 500 x 400mm, Sock - 80mm x
1.2mm
SCK15.V3
SCK15.V3, SCK30.V3, SCK50.V3 Issue 2 (3) 21/09/2023
Handling a Spill - Quick Guide
1 Move away and get help
Make the area safe
2
Assess for injuries
3
4 Identify the spillage
5 Fetch the spill kit
6 Put on appropriate PPE
Limit contamination
7
Contain the spillage
8
9 Mop up the spill
SCK50.V3
50L
Pad (x25), Sock (x5),
Disposal Bag with Ties (x1)
Pad - 500 x 400mm, Sock -
80mm x 1.2mm