Sealey AB125HE Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1. ELECTRICAL SAFETY
p WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A
Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current
Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected by
an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity at Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.
and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none is loose.
1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7. DO NOT pull or carry the appliance by the power cable.
1.1.8. DO NOT pull the plug from the socket by the cable.
1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When an ASTA/BS approved UK
3 pin plug is damaged, cut the cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulation
extends beyond the cable restraint and that the restraint is tight.
Double insulated products, which are always marked with this symbol
To rewire, connect the wires as indicated above - DO NOT connect either wire to the earth terminal.
1.1.10. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance
plugged into it will be protected. The cable core section is important and should be at least 1.5mm
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use of
2.5mm section cable.
2
1.2. GENERAL SAFETY
3 Check that the heater is in sound condition and good working order. Take immediate action to repair or replace damaged parts.
3 Use recommended parts only. Unapproved parts may be dangerous and will invalidate the warranty.
3 Use only paraffin/diesel to fuel your heater, in accordance with instructions contained in this manual.
p WARNING! Only use heater in well ventilated areas. Ensure continuous ventilation is provided to the heater operating area. Ensure a
minimum volume of air of 10m
operation provide at least 80m
outside of the premises in which the heater is to be operated. If your operating area has no direct access to clean fresh air we recommend that
you run a large gauge duct from the outside of the building to the back of the heater in order to provide a clean air intake.
3 Keep the heater a minimum of 3 metres from any combustible materials (i.e. wooden items, cloth, plastics, paper, etc).
3 Maintain a minimum distance of 50cm from non-combustible materials (i.e. brick, steel, concrete, etc).
3 Maintain the following clearances around the heater. Sides - 0.6m, Top - 1.5m, Air inlet - 0.6m, Air outlet - 3.0m
3 Check the colour of the heater outlet to ensure that optimum heat output is maintained.
p WARNING! DO NOT use the heater near flammable material, liquids, solids, gases or compressed gas cylinders and the like.
7 DO NOT allow untrained persons to operate the heater and DO NOT operate the heater without the cover.
7 DO NOT use an external fuel tank. Only use that which is part of the heater.
7 DO NOT leave the heater unattended when in use. Switch the heater off and unplug from the mains before leaving work area.
7 DO NOT stand or place any object less than 3 metres from the heater output.
7 DO NOT obstruct the air inlet and outlet sections of the heater.
7 DO NOT operate the heater when you are tired or under the influence of alcohol, drugs or intoxicating medication.
7 DO NOT over-fill the fuel container. Wipe up any spilt fuel immediately.
7 DO NOT touch the exhaust gas outlet (chimney) at any time due to danger of burns.
7 DO NOT touch the heater outlet when first switched off as these are very hot and will take time to cool.
3 Ensure that the heater is correctly turned off when not in use and store in a safe, dry area, out of reach of children.
2. INTRODUCTION & SPECIFICATIONS
2.1.
Paraffin/diesel heaters with low-fume heat output. Specially constructed stainless steel combustion chamber is vertically vented through
a flue, dramatically reducing the amount of fumes emitted through the hot air nozzle of the heater. Fully specified with safety cut-out and
incorporating a fuel filter for clean, reliable operation. Fitted with an industrial pump for high thermal efficiency and output. Optional nose
cone, Model No.ABNC04 together with standard ducting allows heat to be routed where required with the heater up to eight metres away.
Ideal for heating marquees, village halls and other public areas. Heaters may be controlled by optional remote thermostat, Model No. ABT04.
/kW power and a continuous natural air circulation through windows and doors. For the most efficient
3
/h air flow from outside. This should be divided equally between floor and high level. Ventilation must be to the
3
INSTRUCTIONS FOR:
PARAFFIN SPACE HEATERS
AB125HE & AB180HE
MODELS:
, are fitted with live (brown) and neutral (blue) wires only.
(C/W CHIMNEY)
Yellow & Green
Earth Wire
Blue
Neutral
Wire
Cable
Restraint
FUSE RATING 13 AMP
, but to be absolutely sure that the
2
AB125HE & AB180HE - 1 - 290604
Brown
Live
Wire