Sealey AP260613T Instructions

thank you for purchasing a sealey product. Manufactured to a high standard these products will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCTS CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH THEY ARE INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1. GENERAL SAFETY
WARNING! Ensure Health & safety, local authority, and general workshop practice regulations are adhered to when using these units.

Locate the units in a suitable work area.

Keep the work area clean, uncluttered and ensure there is adequate lighting.

WARNING! use the rollcab on level and solid ground, preferably concrete.

Keep the units clean and tidy in accordance with good workshop practice.

Keep children and unauthorised persons away from the work area.

DO NOT use these units for any purpose other than that for which they are designed.

DO NOT use the units outdoors.

DO NOT place the units in a damp or wet location or an area where there is condensation.

DO NOT clean the units with any solvents which may damage the surfaces or the protective coating.

DO NOT move the units with the drawers out. to avoid tipping, open one drawer at a time and close and secure all drawers whilst

moving the rollcab.
DO NOT step on the drawers.

DO NOT overload the drawers.

2. INTRODUCTION
AP260613T
Heavy gauge steel construction for strength and durability. Sealey embossed topchest lid fitted with gas dampers for smooth opening and
closing. All drawers are on heavy duty ball bearing runners for ease of use and heavier loads. All have stainless steel pulls, non slip liners and
are compatable with Sealey Premier Line tool trays. External features are rust and solvent resistant powder coated finish, heavy duty side
handles and side storage areas. An integral locking system secures all drawers with the turn of one key. for use alone or in combination with
AP26713t rollcab.
AP26713T
As above plus four composite Ø125mm wheels, two with toe locks and two fixed wheels, for easy manoeuvrability using heavy duty side
handles. supplied with two keys.
3. SPECIFICATION
Topchest Model No:
overall size W x D x H:
small Drawer (x5):
top tray:
Rollcab Model No:
overall size W x D x H:
small Drawer (x5):
Large Drawer (x2):
4. ASSEMBLY AND USE
4.1. these units are heavy, obtain the help of at least one other person before attempting to unpack them.
AP26713T
4.2. Attach the wheels to the bottom of the rollcab using 4 bolts and washers per wheel. two of the wheels have brakes on them, ensure
these are fixed to one side.
AP26713T & AP260613T
4.3. fit the side storage areas to the outside using the screws provided.
AP260613T
4.4. to unlock the topchest turn the key clockwise and lift open the lid to allow the two draw locking buttons to disengage and allow the
drawers to be opened. to lock the topchest, close the lid, ensure all drawers are fully in, and turn the key counter clockwise.
AP26713T
4.5. to lock the rollcab, ensure all drawers are fully in and turn the key counter clockwise.
4.6. to remove a draw, the black retaining clips need to be released. Push the left hand side clip down, and pull the right hand side clip up
simultaneously and pull the drawer out. to re-install drawers, place the drawer onto the slides and push in fully.
4.7. Periodically lubricate wheel axles and ensure all nuts and bolts are tight. Lubricate the top and bottom channels of the drawer slides at
least twice a year.
© Jack sealey Limited
AP260613T
678x472x527mm
530x390x50mm
650x420x50mm
AP26713T
770x470x1000mm
530x390x50mm
530x390x130mm
Original Language Version
InstructIons for:
TOPCHEST 5 DRAWER/ ROLLCAB 7 DRAWER,
BALL BEARING RUNNERS, HEAVY DUTY - RED
:
MoDEL no's
AP260613T/AP26713T
AP260613t, 26713t Issue: 1 - 23/05/13