Sealey WORKSAFE 9602L Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
See Specification
Section for Labelling
Refer to
instruction
manual
1. SAFETY
WARNING: Suitable for single-use only. DO NOT re-use.
‰
WARNING: A properly selected coverall is essential to protect your health. Before commencing any task, please consult with qualified safety
‰
personnel to ensure that the coverall type and rating offers adequate protection for your intended use.
WARNING: For use only by trained and qualified personnel.
‰
WARNING: Restrictions on the coverall disposal depend solely on the contamination occurring during use.
‰
When using the coverall with other PPE and in order to comply fully with EN requirement for Type5/6 garments, all openings such as
9
wrist, ankles, neck etc., should be securely taped.
The user shall be the sole judge of the suitability for the type of protection required and the correct combinations of coveralls accessories
9
and ancillary equipment.
Upon contamination, wear or damage, the coverall should be removed and appropriately disposed of at the earliest opportunity.
9
The wearer should always ensure to check the integrity of the coverall before wearing it.
9
The possibility of heat stress should be considered in very warm conditions. Heat stress can be reduced or eliminated by the appropriate
9
use of undergarments and ventilation equipment.
Extreme of heat and cold may adversely affect the performance of this garment.
9
The coverall should not be used where there is a risk to certain hazardous chemicals that have not been tested against. Although limited
9
protection can be offered from various chemicals, please refer to the physical performance of the coverall in relation to Type 5 and 6
testing.
The user must also wear compatible chemical resistant gloves, boots and respiratory protection. The gloves should cover the elastic
9
cuffs. An appropriate size should be selected by the user to allow for unrestricted movement for the intended task.
If necessary please contact Manufacturer/Distributor for advice.
9
It is recommended that the product be used within a period of 3 years from the date of manufacture/production written on the packaging.
9
2. INTRODUCTION
Microporous film makes the coverall breathable, ensuring comfort during periods of extended use. Elasticated wrists, ankles, hood and waist
section. 65gsm Microporous film.
3. SPECIFICATION
Model No:......................................................9602L, 9602XL
Size 9602L Large (Chest/Height): .......... 100-108/176-182cm
Size 9602XL - Extra Large (Chest/Height): 108-116/182-188cm
Fabric Physical Properties
Abrasion Resistance
Flex Cracking Resistance
Trapezoidal Tear Resist. MD
XD
Puncture resistance
Tensile Strength MD
XD
Radioactive Protection
Infective Resistance(solid particles}
Resistance to ignition
Fabric Chemical Properties Test Method
Resistance to chemical EN 368
Sulphuric acid 30%
Sodium Hydroxide 10%
© Jack Sealey Limited
TYPE 5/6 DISPOSABLE COVERALL -
LARGE / EXTRA LARGE
9602L / 9602XL
MODEL NO:
Class
EN 530 Meth.2 Class 1
ISO 7854 B Class 4
ISO 9073·4 Class 2
Class 2
EN863 Class 1
ISO 13934-1 Class 1
Class 1
EN1073-2:2002 Class 2
ISO 22612 Class 3
EN 13274-4 Pass
Penetration Repellency
Class 3 Class 3
Class 3 Class 3
Original Language Version 9602L 9602XL Issue:3 31/03/23