Sealey YK10F Instructions

YK10F YK10FLG YK20
FLOOR
MODELS
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO
MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR
FUTURE USE.
1. SAFETY INSTRUCTIONS
 Familiarise yourself with the applications, limitations and hazards of the press.
 Maintain the press in good condition (use an authorised service agent).
 Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
 Keep the press clean for best and safest performance.
 Locate the press in an adequate working area for its function, keep area clean and tidy and free from unrelated materials and ensure
there is adequate lighting.
 Ensure the workpiece is correctly secured before operating the press.
 Ensure that all fittings are tight before each use.
 WARNING! Always wear approved eye or face protection when operating the press.
 Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain long hair.
 Keep hands and body clear of the work table when operating the press.
 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
 Keep children and unauthorised persons away from the working area.
 DO NOT operate the press if any parts are missing as this may cause failure or possible personal injury.
 DO NOT use the press for a task it is not designed to perform.
 DO NOT adjust or tamper with the safety valve.
 DO NOT exceed the rated capacity of the press.
 DO NOT apply off-centre loads.
 DO NOT allow the workpiece or the arbor plates to fall from the press work bench.
 DO NOT get the press wet or use in damp or wet locations or areas where there is condensation.
 DO NOT operate the press when you are tired or under the influence of alcohol, drugs or intoxicating medication.
 DO NOT climb upon the press.
 When not in use release pressure from the pump and clean the press. Stand or store the arbors in a safe location.
2. INTRODUCTION & SPECIFICATIONS
2.1. GENERAL INFORMATION
The Sealey range of heavy duty floor hydraulic presses are ideal for a variety of workshop applications and are particularly suited to agricultural
or industrial use. Jobs such as straightening, bending, folding, punching, removing bolts and bearings etc are some of tasks that may be
accomplished by your press. Models YK10B, YK10F, YK20 are fitted with a pressure gauge and all models are supplied with work table
arbors.
 DANGER! Models are purpose designed to withstand greater loads than the hydraulic units can develop. For safety reasons, always ensure
the workpiece and press tools are secured on the table and will not flex or suddenly "give way" causing danger to operator or the component.
2.2. SPECIFICATIONS
Model:
Capacity
Ram stroke
Max height ram to table
Min height ram to table
Table aperture
Work table width
Overall height
Gauge included
Weight
3. ASSEMBLY
Unpack the product and check contents. Should there be any damaged or missing parts contact your supplier immediately. Take care to
ensure safety when removing main frame from packing as the unit is very heavy.
3.1. Bench Press Assembly
3.1.1. Identify and lay out parts. Bolt the cross legs to the bottom of the pre-assembled main frame.
3.1.2. Bolt the ram supporting plate or plates to the head of the main frame. Note. If your model has a top and bottom plate which attach
to either side of the frame head, screw the nuts finger tight only at this stage.
3.1.3. Remove the plastic protection ring from the ram thread and apply a suitable thread locking compound, screw the ram into the support
plate until it is tight, thread the locking ring onto the ram on the lower side of the support plate and tighten.
Note. YK20 is not supplied with locking ring.
If the ram passes through two support plates as in 3.1.2 above, you may now tighten the securing bolts.
INSTRUCTIONS FOR :
HYDRAULIC PRESSES
YK10B.V2 YK10BLG
10Tonne 10Tonne
155mm 155mm
390mm 390mm
190mm 190mm
140mm 140mm
360mm 360mm
945mm 855mm
yes
52kg 52kg
Original Language Version
YK10B.V2 YK10BLG
BENCH
MODELS
YK10FLG
10Tonne
203mm
685mm
25mm
83mm
416mm
1425mm
no no
66kg
YK10F, 10FLG, 10B.V2, 10BLG, 20
YK10F YK20
10Tonne 20Tonne
203mm 203mm
685mm 885mm
25mm 22mm
83mm 103mm
416mm 554mm
1514mm 1770mm
yes yes
66kg 131kg
Issue: 1 - 7/6/10