Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
For Sharp Carousel
Models SKM427F9HS or SKM430F9HS
S = STAINLESS
THIS KIT IS UL APPROVED TO ALLOW CERTAIN
MICROWAVE OVENS TO BE INSTALLED ABOVE ANY
ELECTRIC WALL OVEN. REFER TO OVEN OPERATION
MANUAL.
IMPORTANT:
This Built-in Kit is designed for and approved only for those
Sharp Microwave Ovens specifying Built-In Kit SKM427F9HS
or SKM430F9HS. Refer to oven Operation Manual.
IMPORTANT NOTES TO THE INSTALLER
• PLEASE READ THESE INSTRUCTIONS THOROUGHLY
BEFORE BEGINNING INSTALLATION.
• Observe all governing codes, ordinances and safety
instructions.
• Leave these instructions with the consumer.
• DISCONNECT THE PLUG of the microwave oven from the
electrical outlet before installing the Built-in Kit. Remove
the Carousel turntable from the oven cavity.
• Because the kit includes metal parts, due caution should
be used in handling and installation to avoid the possibil-
ity of injury.
ITEM
PART NAME
FRONT FRAME
A
SKM427F9HS: FDECAB283MRK0
SKM430F9HS: FDECAB282MRK0
BACK FRAME
B
SKM427F9HS: FDECAB255MRK0
SKM430F9HS: FDECAB255MRK0
EXHAUST DUCT ASSEMBLY
C
PDUC-B200MRP1
D
SCREW D: XTSS740P20000
Built-in Kit
®
QTY
1
1
1
2
ITEM
E
SCREW E: XOPS740P16000
AIR DEFLECTOR:
F
SKM427F9HS: PREF-B038MRP0
SKM430F9HS: PREF-B039MRP0
A
C
D
F
1
PART NAME
B
C L
E
QTY
8
2
Advertisement
Related Manuals for Sharp SKM427F9HS
Summary of Contents for Sharp SKM427F9HS
- Page 1 ELECTRIC WALL OVEN. REFER TO OVEN OPERATION MANUAL. IMPORTANT: This Built-in Kit is designed for and approved only for those Sharp Microwave Ovens specifying Built-In Kit SKM427F9HS or SKM430F9HS. Refer to oven Operation Manual. IMPORTANT NOTES TO THE INSTALLER • PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION.
- Page 2 • If the dimension of DEPTH (C) is more than 21" (533.4 mm), the outlet location may be any area on the rear wall. The opening in the wall or cabinet must be within the following • The floor of the opening should be constructed of plywood dimensions: strong enough to support the weight of the oven and floor OPENING SKM427F9HS, SKM430F9HS load (about 100 lb/45 kg). The floor should be level and 90˚ with the face of the cabinet for proper installation and Height (A) 14 " - 15 " (368.3 - 400 mm) operation of the oven. Check the local building code that...
- Page 3 STANDARD INSTALLATION INSTRUCTIONS 4. BACK FRAME INSTALLATION: Position BACK FRAME with equal space top to bottom, side to side. Mark for 4 holes, center punch and pre-drill the cabinet with " drill bit. Secure frame with 4 SCREWS E. See Figure 7. Mounting holes Mounting holes Screw E Screw E Equal gap side to side Equal gap top, bottom FIGURE 4 Screw E Screw E Mounting holes...
- Page 4 • Allow minimum 3" (76 mm) wood gap between the The opening in the wall or cabinet must be within the following microwave oven cutout and the appliance cutout below dimensions: the microwave oven. See Figure 2. OPENING SKM427F9HS SKM430F9HS " (628.7 mm) " (628.7 mm) Width (B) " (689 mm) " (768.4 mm) Height (C) "...
- Page 5 FLUSH INSTALLATION INSTRUCTIONS STEP 2 - EXHAUST DUCT ASSEMBLY INSTALLATION 1. Place the Exhaust Duct Assembly in the center of the opening. Align the front edge of the duct with the front of the cabinet. Align the front edge of the right side of the duct with the front of the shelf. See Figure 3. 2. Secure the Exhaust Duct Assembly with 2 SCREWS D. Foot See Figure 3.
- Page 6 FLUSH INSTALLATION INSTRUCTIONS 4. BACK FRAME INSTALLATION: Position BACK FRAME 6. FRONT FRAME INSTALLATION: Place the FRONT equal space top to bottom, side to side. Mark for 4 holes FRAME onto the BACK FRAME and align ball studs on the installed wood cleats, center punch and pre-drill and receivers. Secure the FRONT FRAME to the BACK " drill bit. Secure frame with 4 SCREWS E. See with ⁄ FRAME by firmly pushing the FRONT FRAME onto the Figure 7.
- Page 8 SHARP ELECTRONICS CORPORATION For any other assistance or information about this kit, please call Sharp’s Customer Assistance Center at 100 Paragon Drive, Montvale, New Jersey 07645 1-800-BE-SHARP (1-800-237-4277) TINSEB618MRR0 Dec 2, 2022...