Sealey SBF12 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1. ELECTRICAL SAFETY. p WARNING! It is the user’s responsibility to read, understand and comply with the following:
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs and all electrical
connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An RCCB (Residual
Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD (Residual Current Device) is used with all
electrical products. It is particularly important to use an RCD together with portable products that are plugged into an electrical supply not protected by an RCCB. If
in doubt consult a professional electrician. You may obtain a Residual Current Device by contacting your Sealey dealer. You must also read and understand the
following instructions concerning electrical safety.
1.1.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on a business premises, to be tested by a qualified Electrician at
least once a year by using a Portable Appliance Tester (PAT).
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance, and the safety of the
appliance operator. If in doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the mains power supply. See 1.1.1. & 1.1.2. above and use a Portable
Appliance Tester (PAT).
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply, leads, plugs and all electrical connections for wear and damage, especially power
connections, to ensure that none are loose.
1.1.6. Important: Ensure the voltage marked on the product is the same as the electrical power supply to be used, and check
that plugs are fitted with the correct capacity fuse. A 13Amp plug may require a fuse smaller than 13Amps for certain products.
1.1.7. DO NOT pull or carry the powered appliance by its power supply lead.
1.1.8. DO NOT pull power plugs from sockets by the power cable.
1.1.9. DO NOT use worn or damage leads, plugs or connections. Immediately replace or have repaired by a qualified
Electrician. A U.K. 3 pin plug with ASTA/BS approval is fitted. In case of damage, cut off and fit a new plug according
to the following instructions (discard old plug safely).
(UK only - see diagram at right). Ensure the unit is correctly earthed via a three-pin plug.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
After wiring, check there are no bare wires, that all wires have been correctly connected and that
the wire restraint is tight.
Double insulated products are often fitted with live (BROWN) and neutral (BLUE) wires only. Double insulated products are always marked with this symbol.
To re-wire, connect the brown & blue wires as indicated above. DO NOT connect the brown or blue to the earth terminal.
1.1.10. Some products require more than a 13Amp electrical supply. In such a case, NO plug will be fitted. You must contact a qualified Electrician to ensure a 30 amp fused
supply is available. We recommend you discuss the installation of a industrial round pin plug & socket with your electrician.
1.1.11. Cable extension reels. When a cable extension reel is used it should be fully unwound before connection. A cable reel with an RCD fitted is
recommended since any product which is plugged into the cable reel will be protected. The section of the cable on the cable reel is important. We
recommend that at least 1.5mm
may be used in the other output sockets, we recommend the use of 2.5mm
1.2 GENERAL SAFETY
Disconnect the fan from the mains power when not in use, and before servicing or performing any maintenance.
Use the fan in dry areas only. Do not use in wet or high condensation locations such as bathrooms, showers, or pools.
3
WARNING! If a fan falls into water, immediately switch off and disconnect from the mains power supply. Do not touch the fan until the mains power supply
3
has been disconnected.
p
Always disconnect the fan from the power supply when moving it from one location to another. When not in use store in a safe, dry, childproof location.
Keep the fan clean and maintained in good condition (use an authorised service agent).
3
Use recommended parts only (non genuine parts may be dangerous, and will invalidate your warranty).
3
DO NOT use an extension cord unless it has been approved by an electrical authority.
3
DO NOT stand the fan where it may be knocked over or off a surface, or where the lead may cause a person to trip.
7
DO NOT expose the elderly or children to a continuous air current for long periods of time.
7
DO NOT insert any objects through the fan guard.
7
DO NOT use the fan outdoors
7
7
2. ASSEMBLY
2.1. Attaching the stand to the fan. (See Fig. 1) Remove the fan and the stand
from the carton. The stand must be attached to the fan before the fan is used.
Insert the two circular pillars (A) on the stand as far as they will go into the two
circular holes on the rear cabinet (B). Press both sides of the stand at points (C)
until the two plastic clips snap into place under the rear grille. (see also fig.3)
WARNING! Do not attempt to operate the fan without the stand by proping it
up against a wall or other surface as this may restrict the airflow and cause the
p
motor to overheat resulting in possible damage to property and /or persons. The
fan is designed to be used only with the stand supplied and this must remain
permanently attached. In the event of a stand breakage you must cease to use
the unit until a new Sealey stand part has been obtained and fitted.
section cable but to be absolutely sure that the capacity of the cable reel is suitable for this product and for others that
2
7DO NOT allow children to operate the fan.
7DO NOT immerse the fan in water or any other liquid.
SBF12 & SBF16
INSTRUCTIONS FOR :
Model Nos:
section cable.
2
BOX FANS
Yellow & Green
Earth wire
Blue
Neutra
l
THIS PRODUCT MUST BE FITTED
3 AMP FUSE
WITH A
7DO NOT cover the fan.
fig 1
SBF12 & SBF16 - (F2053) - (1) 020101
Brown
Live
wire
wire
restrai