Sealey HVLP04 Manual

Thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear
instructions respiratory
protection
1. SafeTy
WarninG! disconnect the spray gun from the air supply before changing accessories, servicing or performing any maintenance.
‰
Familiarise yourself with this products application and limitations, as well as the specific potential hazards peculiar to the spray gun.
9
Paint cup remains pressurised after gun is disconnected from air line.
do noT pull the trigger, but release the pressure by gently opening cup.
8
Maintain the spray gun in good condition (use an authorised service agent). Replace or repair damaged parts.
9
Use recommended parts only. non authorised parts may be dangerous and will invalidate the warranty.
9
locate the spray gun in an adequate working area for its function, keep area clean and tidy and free from unrelated materials, and
9
ensure there is adequate ventilation and lighting.
Keep the spray gun clean for best and safest performance.
9
Ensure the air system is suitable to the spray gun air consumption, (see specifications).
9
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and tie back long hair.
9
Keep children and unauthorised persons away from the working area.
9
do noT point spray gun at yourself, at other persons or animals.
8
do noT carry the by the air hose, or pull the hose from the air supply.
8
do noT use the spray gun for any purpose other than for which it is designed.
8
do noT allow untrained persons to operate the spray gun.
8
do noT get the spray gun wet or use in damp or wet locations or areas where there is condensation.
8
do noT operate gun if any parts are missing or damaged as this may cause failure or personal injury.
8
do noT direct air from the air hose at yourself or others.
8
Avoid unintentional operation. When not in use switch the spray gun off, and disconnect from the air supply.
9
2. inTroducTion
Professional gravity feed spray gun with 1mm set-up, ideal for blowing-in small areas of panel where fine control of paint and air is necessary.
Features air and paint flow controls for fine adjustment of spray pattern. HVLP Technology and precision engineering delivers consistent and
unrivalled results. Brass air cap with stainless steel needle and nozzle suitable for water based paints. Alternative set-up available separately.
3. SpecificaTion
Model no: .................................................................HVLP04
Air Consumption: ........................................................... 7cfm
Available Set-Up(s): .................................................... 0.8mm
nett Weight: ................................................................ 0.52kg
Pot Capacity: ............................................................... 100ml
Recommended Air Pressure: ........................................ 22psi
Standard Set-Up: ........................................................... 1mm
4. conTenTS
1.Spanner .......................................................................... x1
2.Cleaning Brush................................................................ x1
3.Strainer ........................................................................... x1
4.Screwed Adaptor- Female thread .................................... x1
5.Spray Gun ....................................................................... x1
5. aSSembly
5.1. empty contents from the product carton on to a tray or bench. In the unlikely event
of missing or damaged parts, inform your Sealey stockist immediately.
5.2. The spray gun has been treated with an anti corrosive agent at the factory and MUST be flushed out thoroughly before use.
5.3. Ensure the strainer, item 3 fig.1, is inserted into the gun port with the stem outermost for easy removal.
5.4. Fit the pot and selected spray head, hand tight only.
© Jack Sealey limited
Touch-up Spray Gun profeSSional
GraviTy feed hvlp 1mm SeT-up
Model no:
Wear eye Wear protective
protection gloves
Original Language Version
hvlp04
Wear protective Wear safety
clothing footwear
1.
2.
3.
4.
fig.1
HVLP04 Issue 1 11/01/19