iSi LL18 Installation

1. Install Load Limiter device to the non-moving rope/
chain near to the anchor/suspension point on a
slacked (non-loaded) hoist.
2. Torque rope clamps down. Cotter pins are simply to
keep the unit in place.
3. For preset units see "sizing overload limit devices".
4. The normally closed contact wires should be
placed in series with an appropriate part of the hoist
circuitry usually the contactor coil of the UP contactor.
As the load increases the switch will open at the ap-
proximate setting and shut down the movement of the
hoist in the UP direction. Slack Load option is put in
WIRE ROPE STYLE
a. Detach the back protection plate.
b. Pick up the heaviest load required ensuring that it is not more than the safe working load of the crane &
hoist combination.
c. Turn the adjusting screw (under protective cover plate) out fully, pick up safe working load, turn adjusting
screw in until cut out then turn back about 1/8 turn and lock. The adjusting screw is very sensitive.
d. Lower the load and lift up again to ensure correct functioning. Do this several times as a check. You may
have to fine tune several times.
e. Reattach back protective plate.
fig. 3b
B
Protective cover plate for adjustment screw.
CHAIN HOIST STYLE
a. Install Chain Load Limiter device using Link pins provided, see table 4.
b. Use the heaviest load required ensuring that it is not more than the safe working load of the crane and hoist
combination.
c. LOOSEN LOCK NUT. Turn the adjusting nut IN (clockwise) to increase the chain load setting and or OUT
(counter-clockwise) to decrease the setting (see fig 4b). The adjusting nut is very sensitive and a small adjust-
ment will cause a relatively large change in setting. The adjusting nut is tight and is constantly under internal
pressure.
d. When desired cut out point is reached, the N.C. contact will open (test several times to assure setting), the
adjusting nut must be locked by tightening the lock nut (see fig 4b).
e. CHECK load cut out again to ensure proper setting. You may have to fine tune.
f.
Ensure that any hoist "top" limit switches are set and arranged so the Chain load limit device could not be
broken by the bottom block when at maximum lift height.
ADJUSTING COLLAR
LINK PIN PLACEMENT—- ONLY USE ISI SUPPLED !!!!
© 2019 Industry Solutions International, Inc.
I NDUSTRY SOLUTI ONS
I N T E R N A T I O N A L, I N C.

Installation of Load Limiters

- Setting in the field:
* USE TORQUE WRENCH to put cable clamp on hoist!
C
WIRE ROPE STYLE
Clamp bolt
– Setting in the field:
LOCK NUT –do not adjust
all the way out.
A
fig. 4b
CHAIN STYLE
B
the DOWN circuit of the hoist.
5. Hysteresis: All electro-mechanical devices exhibit
hysteresis such that to RESET it is likely that the
load must decrease below the "trip point" in order
to reset.
6. Repair of any Load Limit device should not be at-
tempted except for superficial problems such as a cut
wire etc. NEVER disassemble and reassemble any
unit. The "link" pins on the Chain Load Limit devices
are of special grade steel and should never be modi-
fied or replaced with other than factory supplied parts.
(see * Best Torque below)
table 3 Rope Clamp Bolt Torque Rating
Model
LL18, LL28
LL45, LL60
LL80, LL150, LL200
A
fig. 3b Wire rope Hoist Load Limit-
er showing internal mechanics,
rope clamp and cover plate for
adjusting screw.
table 4 Chain Link Pin, Adjusting Collar and Lock Nut sizes
Model Link Pins
Allen
LL12C 6mm
LL17C 10mm 19mm
LL28C 10mm 19mm
fig. 4b Chain hoist load limiter showing adjustment
collar lock nut and link pin placement (included).
Prices and specifications are subject to change without notice.
485 Dundee Avenue, Suite 85
East Dundee, IL 60118, USA
East Dundee, IL 60118, USA
* Best Torque
8 Nm or 5.9 Ft. Lbs.
10 Nm or 7.4 Ft. Lbs.
15 Nm or 11.1 Ft. Lbs.
N.C. Circuit
Adjusting Collar
Hex
13mm 19mm
25mm
25mm
N.C. Circuit
561 Plate Drive, #5
Phone: 847-836-8844
Phone: 847-836-8844
Fax: 847-428-9379
Fax:847-428-9379
Socket
13mm
16mm
19mm
Lock Nut
38mm
50mm
50mm
1
20190603B