Sealey SA20/S Instructions

Item Model & Model & Description
Part No Part No
1 SA20/S-01 SA21/S-01 HOUSING
2 SA20/S-02 SA21/S-02 AIR INLET
4 SA20/S-04 SA21/S-04 TRIGGER
5 SA20/S-05 SA21/S-05 PIN
6 SA20/S-06 SA21/S-06 VALVE STEM
7 SA20/S-07 SA21/S-07 O-RING
8 SA20/S-08 SA21/S-08 SPRING
9 SA20/S-09 SA21/S-09 VALVE PLUG
10 SA20/S-10 SA21/S-10 WASHER
11 SA20/S-11 SA21/S-11 O-RING
12 SA20/S-12 SA21/S-12 THREAD RING GEAR
13 SA20/S-13 SA21/S-13 CAP
14 SA20/S-14 SA21/S-14 GEAR
15 SA20/S-15 SA21/S-15 PIN
16 SA20/S-16 SA21/S-16 GEAR PLATE
17 SA20/S-17 SA21/S-17 CRANK SHAFT
18 SA20/S-18 SA21/S-18 RATCHET ANVIL
19 SA20/S-19 SA21/S-19 RATCHET HOUSING
20 SA20/S-20 SA21/S-20 BUSHING
21 SA20/S-21 SA21/S-21 NEEDLE BEARING
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date. proof of which will be required for any claim. INFORMATION: Call us for a copy of our latest catalogue
and promotions on 01284 757525 and leave your full name and address including your postcode.
Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk.
01284 757500
Original Date: 090500
Issue Date: 090500
Version No: 0
Date Modified: N/A
Item Model & Model & Description
Part No Part No
22 SA20/S-22 SA21/S-22 DRIVE BUSHING
23 SA20/S-23 SA21/S-23 RATCHET YOKE
24 SA20/S-24 SA21/S-24 CYLINDER
25 SA20/S-25 SA21/S-25 ROTOR
26 SA20/S-26 SA21/S-26 ROTOR BLADE
27 SA20/S-27 SA21/S-27 FRONT PLATE
28 SA20/S-28 SA21/S-28 BEARING
29 SA20/S-29 SA21/S-29 END PLATE
30 SA20/S-30 SA21/S-30 BEARING
31 SA20/S-31 SA21/S-31 PIN
32 SA20/S-32 SA21/S-32 WASHER
34 SA20/S-34 SA21/S-34 SPRING
35 SA20/S-35 SA21/S-35 LOCK PIN
36 SA20/S-36 SA21/S-36 RATCHET PAWL
37 SA20/S-37 SA21/S-37 PIN
38 SA20/S-38 SA21/S-38 REVERSE BUTTON
39 SA20/S-39 SA21/S-39 RETAINER RING
40 SA20/S-40 SA21/S-40 SPRING
41 SA20/S-41 SA21/S-41 STEEL BALL
42 SA20/S-42 SA21/S-42 WASHER
01284 703534
E-mail: sales@sealey.co.uk
INSTRUCTIONS FOR
AIR RATCHET WRENCH
SA20/S & SA21/S
Models:
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE
WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
3 Employ all workshop safety rules, regulations, and conditions when using wrench.
p WARNING! Disconnect from air supply before changing accessories or servicing.
3 Maintain the wrench in good condition and replace any damaged or worn parts. Use
genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
p WARNING! Check correct air pressure is maintained and not exceeded. Recommended 70-90psi
3 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each
use and ensure that all connections are secure.
3 Only use impact sockets which are specifically designed for use with a ratchet/impact wrench.
3 Maintain correct balance and foot ing. Ensure the floor is not slippery and wear non-slip shoes.
3 Keep children and unauthorised persons away from the working area.
7 DO NOT use the ratchet for a task it is not designed to perform.
p WARNING! DO NOT use wrench if damaged or thought to be faulty. (Contact Service Agent).
7 DO NOT use wrench unless you have been instructed in its use by a qualified person.
7 DO NOT drop, throw or abuse the wrench as it is a precision tool.
7 DO NOT carry the wrench by the hose, or yank the hose from the air supply.
7 DO NOT operate wrench if you are tired, under the influence of alcohol, drugs or intoxicating medication.
7 DO NOT carry wrench with your hand on the power lever in order to avoid unintentional starting.
7 DO NOT direct air from the air hose at yourself or others.
3 When not in use disconnect from air supply and store in a safe, dry, childproof location.
2. INTRODUCTION & SPECIFICATIONS
The air powered ratchet wrench has a hardened steel anvil and twist-to-reverse mechanism.
With trigger operated power control the wrench is suitable for use in the engine bay where there
is limited space for hand operated rachets.
MODEL . . . . . . . . . . . .SA20/S
Drive size . . . . . . . . . . .3/8”Sq
Max torque . . . . . . . . . . .50ft/lb
Air consumption . . . . . . . .4cfm
Operating pressure . . . . .90psi
Air inlet size . . . . . . . .1/4” BSP
Weight . . . . . . . . . . . . . .1.2kg
MODEL . . . . . . . . . . . .SA21/S
Drive size . . . . . . . . . . .1/2”Sq
Max torque . . . . . . . . . . .60ft/lb
Air consumption . . . . . . . .4cfm
Operating pressure . . . . .90psi
Air inlet size . . . . . . . .1/4” BSP
Weight . . . . . . . . . . . . . .1.2kg
SA20/S, SA21/S - 0016 - (1) -090500