Sealey 2750le.V2 Instructions

thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear safety
instruction footwear
manual
1. Safety
ensure the jack is in sound condition and good working order. take action for immediate repair or
9
replacement of damaged parts. Use genuine parts only. The use of improper parts may be dangerous and
will invalidate the warranty.
locate the jack in a suitable, well lit working area.
9
Keep working area clean and tidy and free from unrelated materials.
9
use jack on level and solid ground, preferably concrete. Avoid tarmacadam as jack may sink in.
9
chock wheels of vehicle.
9
ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear
9
(or "PArK" if automatic).
9
ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow for
9
vehicle tilting.
ensure all non-essential persons keep a safe distance whilst the jack is in use.
9
ensure there are no passengers in the vehicle.
9
Place jack under only those lifting points recommended by vehicle manufacturer (see vehicle handbook).
9
check that the lifting point is stable and centred on the jack saddle.
9
99 ensure the jack wheels are free to move and that there are no obstructions.
9
9
▲ 99 DANGER: Use the jack for lifting only, NOT for supporting the lifted load.
9
99 ensure there are no persons or obstructions beneath the vehicle before lowering.
9
9
use suitable axle stands under the vehicle before proceeding with any task.
9
use a qualified person to lubricate and maintain the jack.
9
99 Do not operate the jack if damaged.
9 8
99 Do not allow untrained persons to operate the jack.
9 8
99 Do not exceed the rated capacity of the jack.
9 8
99 Do not allow the vehicle to move during lifting or lowering, or use the jack to move the vehicle.
9 8
99 Do not jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
9 8
99 Do not work under the vehicle until appropriately rated axle stands have been correctly positioned.
9 8
99 Do not use the jack for purposes other than that for which it is intended.
9 8
99 Do not top up hydraulic system with brake fluid. use hydraulic jack oil only. (sealey Part no: HJo500mls
9 8
or HJo5ls)99
Do not adjust the safety overload valve.
8
9 9 9 When not in use store jack, fully lowered, in a safe, dry, childproof location.
9
9
2. introDuction
twin piston rocket lift feature brings lifting arm straight into contact with the jacking point in 3-4 strokes. universal joint release mechanism
allows safer, more controlled lowering of the jack. Profiled lifting arm gives low clearance height of just 90mm x 390mm deep, making this unit
suitable for sports and custom cars. Heavy-duty chassis with strengthening flanges along the side for extra torsional rigidity under load. fitted
with heavy-duty one-piece hydraulic unit with pump-through action preventing handle locking at maximum ram extension. White saddle aids
positioning under vehicle and safety valve prevents overloading. supplied with foam jacking handle sleeve to prevent damage to the vehicle's
bodywork and integral saddle pad.
3. Specification
model no: ............................................................. 2750le.V2
capacity: ................................................ 2.75 tonne (2750kg)
minimum saddle height: ............................................... 90mm
maximum saddle height: ............................................ 520mm
maximum chassis height: ........................................... 145mm
length: ....................................................................... 700mm
Weight: ........................................................................... 43kg
© Jack sealey limited
instructions for
trolley jack low entry rocket lift
2750le.V2, 3250le.V2
model no:
model no: ............................................................. 3250le.V2
capacity: ................................................ 3.25 tonne (3250kg)
minimum saddle height: ............................................... 90mm
maximum saddle height: ............................................ 530mm
maximum chassis height: ........................................... 152mm
length: ....................................................................... 700mm
Weight: ........................................................................ 45.5kg
Original Language Version
Chock
Wheels
X2
2750le.V2, 3250le.V2 | issue:1 09/01/18
Apply
Never
exceed