Download Print this page
Sealey VMD002 Instructions

Sealey VMD002 Instructions

Vehicle moving dolly - 4 post 900kg max load 430mm min height

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and maintained properly, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Instruction
Wear Safety
Manual
Footwear
1. SAFETY
Ensure the dolly is in sound condition and good working order. Take action for immediate repair or replacement of damaged parts. Use
genuine parts only. The use of non-standard parts may be dangerous and will invalidate the warranty.
WARNING: Prepare the vehicle ready for resting and moving on the dolly. Ensure the vehicle will not move, tip, fall etc.
once it has been seated on the dolly. Take any necessary precautions to protect persons, property and equipment when using.
Locate the dolly in a suitable, well lit working area.
Keep working area clean and tidy and free from unrelated materials.
Use the dolly on level and solid ground, preferably concrete. Avoid tarmacadam as dolly may sink in.
Ensure the vehicle engine is switched off .
Ensure there are no passengers in the vehicle.
Ensure all non-essential persons keep a safe distance whilst the dolly is in use.
Only place dolly under those lifting points recommended by vehicle manufacturer (see vehicle hand book).
Check the lifting point is stable and correctly held in dolly supports.
Ensure the dolly wheels are free to move and that there are no obstructions.
Ensure you have a clear view and necessary assistance when transporting vehicle.
Ensure there are no persons or obstructions beneath the vehicle before moving.
 When required, immobilise the dolly using the brake pedals fitted to each castor.
 DO NOT operate the dolly if damaged.
DO NOT allow untrained persons to operate the dolly.
DO NOT exceed the rated capacity of the dolly.
WARNING: DO NOT use the dolly to hold and move a vehicle which is unstable.
DO NOT allow the vehicle to move on the dolly.
DO NOT move vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
DO NOT ride on the dolly.
DO NOT use the dolly for purposes other than which it is intended.
When not in use store the dolly in a safe, dry, childproof area.
2. INTRODUCTION
Heavy-duty steel frame suitable for supporting partly dismantled or badly damaged vehicles. Enables easy movement around workshop or
bodyshop. Adjustable frame allows you to change the length and width as required. Three interchangeable supports, rubber support pads, shallow
v-crutch and deep v-crutch, that are all height adjustable. Fitted with four Ø200mm nylon locking castors.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VMD002
Minimum Height:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400mm
Maximum Height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 520mm
Minimum Width: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 680mm
Maximum Width: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1280mm
Minimum Length: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1150mm
Maximum Length: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1750mm
Capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 900kg
© Jack Sealey Limited
INSTRUCTIONS FOR:
VEHICLE MOVING DOLLY - 4 POST 900kg
MAX LOAD 430mm MIN HEIGHT
VMD002
MODEL NO:
Original Language Version
VMD002 Issue:2 (SP)- 18/11/16

Advertisement

loading

Summary of Contents for Sealey VMD002

  • Page 1 Model No: ........
  • Page 2 10 . . .VMD002.10 Nut.M10 11 . . .VMD002.11 Spring washer 10mm 12 . . .VMD002.12 Washer 10mm 13 . . .VMD002.13 Bolt M10 x 30 14 . . .VMD002.14 Short pin 12mm 15 . . .VMD002.15 Crutch (narrow angle) 16 .

This manual is also suitable for:

5054511144109