Sealey RS1.V3 Instruction Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: BEFORE USING THIS PRODUCT, PLEASE READ THE INSTRUCTIONS CAREFULLY. MAKE CAREFUL NOTE OF SAFETY INSTRUCTIONS,
WARNINGS AND CAUTIONS. THIS PRODUCT SHOULD ONLY BE USED FOR ITS INTENDED PURPOSE. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. RETAIN THESE INSTRUCTIONS FOR FUTURE USE.
1. GENERAL FEATURES
GENERAL FEATURES
! Initial peak power RS1.V3 - 1000 amps, RS102.V2 - 1600 amps. More than enough to start
most vehicles. May also be used in DEEP CYCLE applications.
! The Roadstart is also a portable power source for accessories equipped with a male cigarette
lighter plug. The DC outlet has automatic 12 amp overload protection.
! Test switch and LED lights. Solid state circuitry.
SAFETY FEATURES
! Safety storage holsters prevent accidental sparking of clamps.
! The Roadstart contains the latest technology with its 12 volt sealed lead acid battery. This
means the Roadstart RS1 & RS102 may be stored in any position without fear of leakage.
IMPORTANT: READ SAFETY INSTRUCTIONS BEFORE ATTEMPTING TO USE THE ROADSTART.
2. SPECIFICATIONS
Built-in battery . . . . . . . . . . . . . .Sealed lead acid, maintenance free, re-chargeable.
DC Output (volts) . . . . . . . . . . . .RS1.V3/RS102.V2 . . . . . . . .12
Peak Current (amps) . . . . . . . . .RS1.V3 . . . . . . . . . . . . . .1000
. . . . . . . . . . . . . . . . . . . . . . . . .RS102.V2 . . . . . . . . . . . .1600
Cold Cranking Current (amps) . .RS1.V3 . . . . . . . . . . . . . . .300
. . . . . . . . . . . . . . . . . . . . . . . . .RS102.V2 . . . . . . . . . . . . .600
Charging Time . . . . . . . . . . . . . .Up to 30 hours with AC charger.
Breaker . . . . . . . . . . . . . . . . . . .12 amp (for DC power port)
Weight . . . . . . . . . . . . . . . . . . . .RS1.V3 . . . . . . . . . . . . . .8.2kg
. . . . . . . . . . . . . . . . . . . . . . . . .RS102.V2 . . . . . . . . . . . . .9kg
Dimensions (mm) . . . . . . . . . . . .RS1.V3 . . . . . .335 x 260 x 90
. . . . . . . . . . . . . . . . . . . . . . . . .RS102.V2 . . .335 x 235 x 130
3. SAFETY INSTRUCTIONS
F  DANGER! - RISK OF EXPLOSIVE GASES.
p WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL OPERATION.
FOR THIS REASON, IT IS VERY IMPORTANT TO READ AND FOLLOW THESE INSTRUCTIONS EXACTLY EACH TIME YOU USE THE RS1, RS102 or RS2.
IMPORTANT: To reduce risk of battery explosion, follow these instructions and those published by battery manufacturer and manufacturer of
any equipment you intend to use in vicinity of the battery. Remember to review warning marks on all products and on engines.
3.1. PERSONAL PRECAUTIONS
Ensure there is another person within hearing range of your voice, or close enough to come to your aid should a problem arise when
!
working near a lead-acid battery.
Have fresh water and soap nearby in case battery acid contacts skin, clothing or eyes.
!
Wear safety eye protection and protective clothing. Avoid touching eyes while working near battery.
!
Wash immediately with soap and water if battery acid contacts skin or clothing. If acid enters eye, flush eye immediately with cool, clean
!
running water for at least 15 minutes and seek immediate medical attention.
Remove personal metallic items such as rings, bracelets, necklaces and watches. A lead-acid battery can produce a short-circuit current
!
high enough to weld a ring or the like to metal, which may cause severe burns.
3.2. OTHER IMPORTANT SAFETY INSTRUCTIONS
!
Familiarise yourself with the application, limitations and potential hazards of the unit.
Keep the unit in good working order and condition. Take immediate action to repair or replace damaged parts.
!
Only use recommended attachments and parts. To use unapproved items may be dangerous and will invalidate your warranty.
!
The Roadstart must only be opened and checked by qualified service personnel. DO NOT disassemble for any reason.
!
Keep children and unauthorised persons away from the work area.
!
Keep work area clean and tidy and free from unrelated materials and ensure that there is adequate lighting.
!
If the unit receives a sharp knock or blow, it must be checked by a qualified service agent before being used.
!
When not in use re-charge every six (6) months.
!
DO NOT smoke or allow a spark or flame in the vicinity of the battery or engine.
%
DO NOT drop any metal tool onto the battery as it may spark or short circuit the battery, which could cause an explosion.
%
DO NOT use the unit to recharge dry cell batteries that are commonly used with home appliances. These batteries may burst and cause
%
injury to persons and damage to property.
DO NOT charge or boost a frozen battery.
%
DO NOT allow clamps to touch each other, or to contact the same piece of metal, as this will result in arcing.
%
DO NOT use attachments other than those recommended. To do so may risk damage to the unit, equipment and possible injury.
%
I N S T R U C T I O N M A N U A L F O R :
PORTABLE ROADSTART UNITS
RS1.V3
&
1) Safety storage holsters
2) ‘Charged’ Indicator light
3) Multiple LED power indicator
4) Heavy duty thermo-plastic case
5) TEST switch
6) 12V DC output / charging socket
7) Heavy duty clamps
8) Flexible heavy duty copper cables
9) Wall charger
10) DC charging / output cable
AC Charging
Adaptor
RS102.V2
DC Charging
Cable
RS1.V3 & RS102.V2 - 1 - 191203