Sealey REG/MO.V2 Instructions

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will,if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT: Please read tHese instruCtions CareFullY. note tHe saFe oPerational reQuireMents,
Warnings and Cautions. use tHis ProduCt CorreCtlY and WitH Care For tHe PurPose For WHiCH it is
intended. Failure to do so MaY Cause daMage and/or Personal inJurY and Will inValidate tHe WarrantY.
Please KeeP instruCtions saFe For Future use.
1. saFetY instruCtions
read the following instructions carefully before using the regulator, and
keep them for future reference. the instructions provide all the
information necessary for correct use of the regulator, to avoid damage
and danger.
sEALEY will not be responsible for any damage occurring due to
incorrect use of the regulator, or to modifications made to it. this gas
regulator is a delicate piece of workshop equipment. Failure to observe
the following safety points will cause damage to the unit and will
invalidate your warranty.
 use regulator only for gas intended.
 use to designed pressure.
 check for damage and leaks at frequent intervals.
 do not knock or jolt regulator.
 do not use a regulator showing any signs of damage.
 do not allow cylinders to become heated.
 do not use pressure gauges that are damaged, not smooth in
operation or not zeroing.
 do not overtighten adjusting knob as this will damage diaphragm
and void warranty.
 do not oil the regulator.
 Warning! Incorrect use of the regulator can cause serious
damage. users must be trained by specialist engineers.
 Warning! the regulator must be treated as a precision instrument.
Protect it from accidental knocks, dust, oil and other sources of dirt.
 Warning! Do not use the regulator if it is not in perfect working
condition
 Warning! When you draw gas, the cylinder must be placed upright
and protected from falling.
reg/Mo.V2, reg/Mt.V2
InstructIons For
industrial gas regulators
2. introduCtion & sPeCiFiCation
2.1 top quality regulators made to En Iso 2503, manufactured from only
the highest quality materials and machined almost entirely automatically
to fine tolerances. With correct use they will give reliable and trouble free
service. suitable for industrial size gas cylinders, these regulators are
designed only for use with the shielding gases carbon Dioxide, Argon or
a mixture of these two gases (when used with the correct adaptor). Do
not use for any other purpose.
2.2 sPeCiFiCation: .................... reg/Mo ...............................reg/Mt
cylinder type................................. Industrial .............................. Industrial
Gauge .........................................................1 ...........................................2
Argon/co Adaptor .................................Yes .......................................Yes
²
safe Working Pressure (Inlet) .......... 230bar ................................. 230bar
Max outlet pressure ............................. 4bar ..................................... 4bar
Max throughput .............................10ltr/min ...............................10ltr/min
KeY to MarKings (stamped on regulator bodies)
relevant 'K' = Pressure
standard reducer class
en iso 2503
Gas code 'n' = co
the function of the regulator is to reduce and control the pressure of a
gas. the regulator reduces the cylinder pressure at which the gas is
stored, to the pressure needed to use the gas.the pressure reducer has
been designed so as to be used only and exclusively with the type of gas
and at the pressure which are shown by the markings stamped on the
regulator body (refer to the markings key above ).
 Warning!to try and use the pressure reducer with types of gasses
and pressures other than those indicated can be dangerous.
:
2.
code for serial
gas type number
K1 n 170409 230Bar
, Argon and co /Argon mix
² ²
rEG/Mo.V2, rEG/Mt.V2
introdu-
Max inlet
pressure
Issue no.1 11/09/09