Sealey MC680A Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear protective
instruction gloves
manual
1. SAFETY
Disconnect lift from air supply before changing parts, servicing or performing any maintenance.
9
WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 100-120psi. Required air flow 9.5cfm.
‰
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use, and ensure that all connections are secure.
9
Ensure lift is kept clean and in good working order. Immediately repair or replace damaged parts.
9
Use recommended parts only. Incorrect parts may be dangerous and will invalidate the warranty.
9
Use a qualified person to lubricate and maintain the lift. DO NOT use brake fluid to top up system. Use Sealey hydraulic oil only.
9
9 Locate lift in a suitable, well lit work area. Keep area clean and tidy and free from unrelated materials.
9
9
Use lift on level and solid ground, preferably concrete. Avoid tarmacadam since lift may sink in.
9
Ensure all non-essential persons keep a safe distance.
9
Always keep your hands and feet away from moving parts. DO NOT reach under the lift.
9
9 9 DO NOT operate the lift if parts are missing or damaged.
9 8
9 9 DO NOT adjust the safety overload valve.
9 8
Keep the lift clean for best and safest performance.
9
The maximum load is 680Kg. DO NOT exceed this rated capacity.
9
Use this lift for lifting purpose only. DO NOT use it for any other purpose it is not designed to perform.
9
Keep children and unauthorised persons away from the work area.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain long hair.
9
Keep proper balance and footing, DO NOT overreach and wear non-slip footwear.
9
Ensure the vehicle is adequately secured to the lifting platform with appropriate straps.
9
When the platform is being raised, ensure the safety handle is moved to the right hand side of its detent, to engage the safety plate,
9
(see section 6.1.5).
Before lowering lift ensure that there are no obstructions underneath and that all persons are standing clear.
9
DO NOT use the lift if damaged, any suspect parts are noted or it has been subjected to a shock load.
8
DO NOT operate the lift when you are tired or under the influence of alcohol, drugs or any intoxicating medication.
8
DO NOT allow untrained persons to operate the lift.
8
DO NOT make any modifications to the lift.
8
DO NOT get the lift wet.
8
9 9 DO NOT pull the hose from the air supply, and DO NOT direct air from the air hose at yourself or others.
9 8
9 When not in use disconnect lift from the air supply, and store in the down position in a safe, dry, childproof area.
9
9
WARNING: The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions
‰
and situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this
product, but must be applied by the operator.
2. INTRODUCTION
All steel construction with both hydraulic pump and air motor assembly. Combined air and foot pump separate from main lift for choice of operation.
Ramp and platform made with chequer plate surface to ease loading and positioning of motorcycle. Supplied with motorcycle front wheel locking
attachment, securing vehicle to provide easy maintenance access. Fitted with safety lock to prevent accidental lowering. Suitable for use with centre
stand motorcycles or with paddock stand.
MT680.V4: Features two additional side platforms for extra width.
3. SPECIFICATION
Model no: ......................................................... MC680A ............................................................MT680.V4
Capacity: ............................................................... 680kg ................................................................... 680kg
Minimum height:.................................................. 190mm ................................................................. 190mm
Maximum height: ................................................. 790mm ................................................................. 790mm
Width: ................................................................. 710mm ................................................................. 710mm
Width with side platforms: ............................................................................................................... 1220mm
Length: .............................................................. 2000mm ............................................................... 2000mm
Air Supply: ..................................Min.100psi/Max.120psi .........................................Min.100psi/Max.120psi
© Jack Sealey Limited
MOTORCYCLE LIFT 680KG CAPACITY
HEAVY-DUTY AIR/HYDRAULIC
MINI-TRACTOR, QUAD & MOTORCYCLE LIFT
680KG CAPACITY AIR/HYDRAULIC
MODEL NO:
Wear safety Warning:
footwear Crushing of
Hands
Original Language Version
MC680A / MT680.V4
MC680A, MT680.V4 Issue:2 (3,9,F) - 29/05/19
9 9