Sealey SJBEX200.V2 Manual

Thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. safeTy
9
ensure the beam is in sound condition and good working order. Take action for immediate repair or replacement of damaged parts. Use
genuine parts only. The use of improper parts may be dangerous and will invalidate the warranty.
9
Inspect the beam before each use. DO nOT use the beam if it is damaged, altered, modified, in poor condition, leaking hydraulic fluid, or
unstable due to missing parts.
8
DO nOT alter or modify this beam in any way.
8
DO nOT load the beam beyond its rated capacity.
8
DO nOT operate the beam if damaged.
8
DO nOT allow untrained persons to operate the beam.
8
DO nOT use the beam for purposes other than that for which it is
intended.
8
DO nOT use the centre saddle if the work to be perform can cause
the load to move.
8
DO nOT top up hydraulic system with brake fluid. Use hydraulic jack
oil only.
9
Use the beam only for its intended purpose.
9
Consult the vehicle manufacturer for the correct lifting locations.
9
Make sure the vehicle is in park and the handbrake is on before
attempting to raise the vehicle.
9
only use the saddles provided with the jacking beam.
9
Be sure setup is stable and secure before lifting. Be careful of pinch points.
9
This is a lifting device only. Make sure the load is central on saddles before lifting.
9
The beam can only be used to lift one end of the vehicle.
9
ensure that there are no persons or obstructions beneath the vehicle before lowering.
9
Always lower load slowly and carefully.
9
When not in use store beam fully lowered.
9
ensure all non-essential persons keep a safe distance whilst the beam is in use.
9
Use a qualified person to maintain or repair the beam's hydraulic system.
‰
WaRning! Failure to heed these precautions may result in loss of load, damage to beam and/or personal injury.
2. inTRODucTiOn
Fully certified and approved to comply with MoT requirements. Features two-stage mechanical safety lock and telescopic finger guards to
prevent accidental injury. Supplied with two pairs of aluminium support blocks. Beam has spring loaded flat arms with roller bearings - when
unloaded, these support the weight of the beam, allowing the entire unit to run smoothly along the pit or ramp, but when loaded locate the unit
firmly. optional hook arms supplied. Wide lift configuration meets MoT recommendation for lifting on jacking point.
3. specificaTiOn
Model .............................. SJBeX200.V2..................SJBeX300
Capacity .....................................2tonne.........................3tonne
Support Arm Reach .......... 780-1075mm..............780-1075mm
Beam lift .............................. 95-300mm..................95-300mm
load Arm Reach ............... 850-1600mm..............850-1600mm
net Weight .....................................94Kg.........................102Kg
4. pRepaRaTiOn
‰
WaRning! These jacking beams weigh 94kg and 102kg respectively. Seek
assistance before attempting to locate jacking beam on ramp or inspection
pit runners.
4.1. Locating jacking beam.
4.1.1. Extend the roller arms to the correct width for ramp or pit runners. fig.4.
© Jack Sealey limited
Jacking beams
Model no:
Wear protective Wear safety
gloves footwear
Original Language Version
sJbeX200.V2 & sJbeX300
Wear protective
clothing
fig.1
fig.2
SJBeX200.V2, SJBeX300 | Issue 6 (2) 14/08/18