Eskimo HD07 Instruction Sheet

InstructIon guIde for eskImo Hand augers
Thank you for purchasing an Eskimo® Hand Ice Auger from Ardisam, Inc. We
have worked to ensure that the ice auger meets high standards for usability and
durability. With proper care, your ice auger will provide many years of service.
Applies to models: HD06, HD07, HD08 (Standard Blades) and BHA6 and BHA8
(Barracuda Blades).
Before usIng your Ice auger, rememBer:
1) Always leave your blade protector on when not using your Eskimo hand auger.
The blades are sharp and can cause injury if proper precautions are not taken.
2) Be extremely careful when using your auger in shallow waters, as a rocky
water bottom can damage your blades and the auger if they come in contact.
3) Never try to adjust the cutting angles of your auger blades, especially by bending
them. The angles are specifically engineered and critical to the auger' s performance.
4) Always start a new ice hole instead of reopening an old one with your ice
auger. The sides of an old ice hole often freeze, shrinking the hole's diameter.
This can cause your auger to jam. Using your ice auger in these conditions
can damage the auger and blades.
5) When using your ice auger, remember that the under-surface of ice is often uneven.
This can cause your auger to become jammed as you break through the ice. If you
find yourself in this situation, do not force your auger. Lift it up approximately 1" and
make several half turns, lowering the drill 1/4" each turn until a clean hole is cut.
6) Never hit your auger on the ice when trying to start a hole, as this can bend your
auger and damage the blades. Lower your auger gently when starting to drill.
assemBly
To assemble your Eskimo hand auger, insert the pommel handlebar assembly into
the auger weldment. The handle can be adjusted to three different lengths (52",
56" or 60") by aligning the appropriate hole on the handle bar with the hole in the
auger weldment. To secure the handle in place, insert the wing bolt and tighten.
sHarpenIng
Sharp blades make cutting through ice easier. If your auger becomes dull, a new
set of blades can be ordered from Eskimo. Eskimo also offers a blade exchange
program. Contact customer service at 1-800-345-6007 for more information.
Replacement parts can also be found by visiting our website, www.geteskimo.
com.
If sharpening blades on your own, first remove the blades and then use a fine stone
to hone the upper surface only. Stoning on the wrong side, even just the slightest
amount, can damage the blade and make it ineffective. Blades must be razor sharp
with no nicks, dents or scratches, to work properly.
one-year lImIted Warranty
Ardisam, Inc., a manufacturing company, warrants this Eskimo Hand Auger to be free from defects in the material or workmanship for a period of one year from the date of
purchase. During the one-year warranty of this product, Ardisam will, at its discretion, furnish parts and labor to correct any defect caused by faulty material or workmanship. To
obtain warranty service and/or replacement instructions, you must have prior approval before shipping package by calling our customer service department at 1-800-345-6007
for a return material authorization number (RMA#). All items must be shipped prepaid. Ardisam, Inc. will at no charge, repair or replace, at their discretion, any defective part
which falls under the conditions stated above. Ardisam retains the right to change models, specifications and price without notice. This product if used as intended, will give you
years of trouble free service. We hope you will enjoy the quality of our products for years to come. For replacement parts, phone 1-800-345-6007 or go online to GetEskimo.com.
This warranty applies to the original owner with a proof of purchase and is not transferable. It supersedes all other warranties either expressed or implied and all other obligations
to liabilities on our part. Ardisam, Inc. does not assume, and does not authorize any other person to assume for us, any liability in connection with the sale of our products. The
warranty applies only to products which have not been subjected to negligent use, misuse, alteration, accident or repairs made by anyone not certified by Ardisam, Inc. This
guarantee is void unless the warranty card is properly filled out and received by Ardisam, Inc., within 30 days of purchase.
Check for parts online at www.geteskimo.com or call 800-345-6007 M-F 8-5 CST
BALLOON #
P A R T # D S E C R P I
1 252V HB W/1018V POMMEL COMPLETE
2 267F HAND AUGER WELD
3 300 8 INCH HAND BLADE FINISH
4 8651 RUBBER STRAP BLADE PROTECTOR
5 63285 WING BOLT (THREADED) HAND AUGER
6 BPH7 7" HAND AUGER BLADE PROTECTOR
7 IB5810 BOLT 5MM X 0.8 X 10MM HH ZN
parts BreakdoWn and replacement parts
pommel handle
bar assembly
Auger weldment
Blade protector
and rubber strap
part no.
252V HANG AUGER HANDLE WITH poMMEL
1018V HAND AUGER HANDLE poMMEL
63285 WING BoLT, HANG AUGER
303A BLADE pRoTECToR (FoR HD06, 6" STANDARD AUGERS)
304 BLADE pRoTECToR
(FoR HD07 AND HD08, 7" AND 8" STANDARD AUGERS)
2320A BLADE pRoTECToR (FoR BHA8, 8" BARRACUDA AUGERS)
2319 BLADE pRoTECToR (FoR BHA6, 6" BARRACUDA AUGERS)
RB6 HAND AUGER BLADES 6" (STANDARD)
RB7 HAND AUGER BLADES 7" (STANDARD)
RB8 HAND AUGER BLADES 8" (STANDARD)
BRB6 TURBoCUT HAND BLADES 6" (BARRACUDA)
BRB8 TURBoCUT HAND BLADES 8" (BARRACUDA)
T O I N Q Y T
1
ED 7"AND 8" ICE 1
2
Eskimo Hand Augers
1
1
1
4
Wing Nut
Hd08 shown with standard blades
please note that turbocut blades are
curved for speed, while standard blades
are straight for longer life.
Auger blades
(Blades shown are Standard blades
for HD08. TurboCut blades are on
Barracuda models.)
descrIptIon
Instruction Sheet
ISHANDAUGERS
Rev. 02/23/11
©2011 Ardisam, Inc.
All Rights Reserved.