Samsung SH-D162D User Manual

SH-D162D(TS-H352D)ENG/RUS 2007.5.30 11:55 AM Page 1
DVD-ROM DRIVE
SH-D162D(TS-H352D)
User Guide - ENGLISH
FCC Compliance
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be
deter-mined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Change or modifications not expressly approved by the manufacturer responsible for
compliance could void the user 's authority to operate the equipment.
LASER STANDARD
IEC 60825-1 :1993 +A1 :1997 +A2 :2001
WEEE
Correct Disposal of This Product (Waste Electrical &Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature,indicates that it should not be disposed with
other household wastes at the end of its working life.To prevent possible harm to the
environment or human health from uncontrolled waste disposal,please separate this from other
types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product,or their
local government office,for details of where and how they can take this item for environmentally
safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase
contract.This product should not be mixed with other commercial wastes for disposal.
• Samsung Eco-mark
The Samsung's own Eco mark helps consumers to easily understand that
Samsung develops eco-friendly products. This mark represents Samsung's
continuous effort to develop eco-friendly products.
• RoHS
(Restriction of the use of certain hazardous substances in electrical and electronic equipment)
The RoHS, the environment regulation announced by European Union, restricts the use of
lead, mercury, cadmium, hexavalent chromium, PBB, and PBDE in products put on the
market in The European Union after July 1, 2006.
- http://www.samsung-ODD.com
- http://www.samsung-ODD.com
BG68-01434A Rev.00
When using one EIDE cable
•
Connect the cable to the SL (Slave) of the Master/Slave Select Terminal at the rear
of the DVD-ROM drive.
Slave Drive (Choose the SL Jumper)
MainBoard
Hard Drive
When using two EIDE cable
• Connect the cable to the MA (Master) of the Master/Slave Select Terminal at the rear
of the DVD-ROM drive.
- If there is only one Optical drive: select MA (Master).
Master Drive (Choose the MA Jumper)
SEC 1
PRI 1
MainBoard
Hard Drive
-If there is two Optical drive, select MA (Master) / SL (Slave).
Master Drive (Choose the MA Jumper)
Slave Drive (Choose the SL Jumper)
SEC 1
PRI 1
(Choose the MA Jumper) (Choose the SL Jumper)
Hard Drive
MainBoard
5
All manuals and user guides at all-guides.com
Safety Precautions
The following are basic precautions to ensure user safety
and reduce the risk of property damage.
When you install the drive
Place the drive on a level
surface.
• Avoid high-humidity environments.
• Failure to do so may cause the
device to fall onto a hard surface,
resulting in damage or malfunction.
While operating
• If the power cable is not connected
properly, it may cause a fire or
damage the drive. Check the direction
• Avoid low- or high-temperature
of the power connector and the drive
environments.
incline before connection.
+5V DC Ground
Ground +12V DC
Other
Handle with caution to prevent
• damage from external shock.
Do not place the drive in
direct sunlight.
• Any change or modification not expressly approved by designated qualified personnel could
void your authority to operate this device.
Important to read and understand
Do not disassemble
at all times
1
Installing the Drive
System Requirements
Intel Pentium II 350MHz(or higher), 128 MB of RAM (or higher) with an EIDE interface,
Windows 2000/XP/Vista / Windows NT 4.0 (or higher)
Installing the DVD-ROM Drive
How to install the DVD-ROM drive on your PC. First, remove the cover;
connect the cable to the DVD-ROM drive and then to the PC.
1
If necessary, attach a horizontal bracket
to both sides of the drive.
• You can purchase these accessories separately
from your computer dealer.
(Screws for use: M3 X 6 X 4)
2
Remove the plate from a free expansion slot and install the
DVD-ROM drive, as shown in the illustration.
• If you have no free expansion slot, install the drive in place of the
diskette drive.
• Make sure to use the standardized screws supplied (M3X6).
- To use screws other than M3X6 may result in malfunction.
DVD-ROM
Plate
Drive
Horizontal
Bracket
6
Warning/Caution
Warning:
To warn the user that failure to comply with the instructions may result in
serious injury or death.
Caution: To caution the user that failure to comply with the instructions may result in
damage to property.
Do not drop the drive, and
• Never allow food particles or
protect it fromsevere shocks.
foreign substances to enter the
• It can damage the drive or cause
drive casing.
it to malfunction.
Do not move the drive while in operation and
do not attempt to open the disc tray byforce. •
To protect against the risk of
Make sure to close all working programs before
fire, do ot spill such liquids as
attempting to open the tray and always use the
alcohol and benzene on the
open/close button.
drive.
Do not insert a pin into the emergency
opening while in operation.
Do not use cracked, distorted or
Do not disassemble, attempt to repair
damaged discs.
or modify the device without express
approval as directed in the manual.
• To reduce the risk of damage,
electric shock, and fire.
In particular, a disc with a crack on the
inner tracks may break while in use.
1. Check to see that the disc does not have a crack before use. If the disc has a crack (especially around the center hole), it is recommended that
you make a copy immediately and use the copy instead. When a cracked disc is used continuously,the size of the crack is likely to grow and it
will eventually result in irreparable damage to the disc.
2. Do not use low quality discs (i.e., illegal products, scratched or damaged discs).
2
Using the Drive/Storing and Cleaning
Your Discs
Using the DVD-ROM Drive
1
Push the power button and boot the computer.
2
After booting the computer, open the disc
compartment by pressing the Eject button.
3
Insert the disc (CD) with the label on the disc
facing upwards and close the disc compartment
by pressing the Eject button. The indicator light
comes on.
4
Play the disc (CD).
Playing CD-DA/Audio CDs
•
Run the CD player program supplied with the sound card or play the
Windows Media Player.
Playing Video CDs
•
Follow the instructions provided with the disc.
• A video card or MPEG software and a sound card need to be installed to view video CDs.
• If the drive is vertically installed, you cannot use an 8 cm Mini Disc
because the disc is movable.
Storing Your Discs
•
Do not place a disc in direct sunlight.
• Store a disc vertically in a well-ventilated and
stable location.
• Do not write or attach a label on a disc.
•
Do not drop a disc or place heavy objects on it.
Cleaning Your Discs
• Do not touch the surface • To clean a disc, polish lightly
of a disc; hold it by the from the inside of the disc to the
edges. outside with a soft cotton cloth.
• The disc may not function properly if there are fingerprints, foreign substances or
dust on the disc surface.
7
Introduction
• Design and specifications are subject to change without prior notice.
Eject Button
Front
Disc compartment LED
Emergency eject hole
If the compartment does not open
when you press the Eject button,
power off the computer, insert a pin
or unfolded paper clip in the hole
and push firmlhy)
Sound output terminal Interface terminal
Rear
Digital output Master/slave select terminal Power terminal
terminal
Accessories
User Guide, Screws.
Design and specifications are subject to change without prior notice.
3
Solving Technical Problems
• The friction noise generated during SPIN-UP and STOP is caused by the
Automatic Ball Balancing System(ABS) and is not a malfunction.
The DVD-ROM drive is not •
Check that the power, audio and EIDE cables are correctly
detected by the computer. connected to the computer.
•
Change the EIDE cable and reconnect it to the computer.
Preferably, connect a second EIDE cable to the DVD-ROM
After installing the DVD-ROM
drive in master mode.
drive, the PC gets slower.
• Check the position of the jumper in the master/slave select
terminal.
The DVD-ROM drive is not
• Reinstall the device driver or update it with the latest version
recognized by MS-DOS.
by downloading it from the Samsung Web site.
- http:// www.samsung-ODD.com
- http:// www.samsung.com
The DVD-ROM drive is not •
This case may occur when there is a Windows installation
detected by Windows. problem; reinstall Windows.
A CD is not read or is read •
Check whether the CD is of good quality and clean it,
if necessary.
too slowly.
The disc compartment will
• Check that the power cable is correctly connected.
not open. •
Power off and disconnect the PC.
Insert a pin or unfolded paper clip in the emergency hole and push
firmly until the disc compartment opens.
When the MPEG software •
Adjust the size of the replay screen.
plays a Video CD, the pictures • After checking the display resolution, adjust it, if necessary.
are not regular and the running
speed is too slow.
The Disc is not in message is • The computer may not recognize the disc if you start playback
displayed even though a disc too quickly after inserting the disc.
Open and close the disc compartment and try again.
has been inserted.
•
Clean the disc and try again.
The DVD-ROM drive is not •
The interface mode of the sound card is AT-BUS.
detected after it is connected You must therefore connect the DVD-ROM drive to the EIDE
to a sound card. port on the PC mother board, rather than to the sound card,
or install an EIDE compatible sound card.
8
Connecting the Cables to the
DVD-ROM
Connecting the Cables
Power cable
EIDE cable
Master/slave select terminal
Audio cable
1 Connecting the power cable
• The 4-pin power cable from the internal power unit of your computer must
be connected to the power terminal the rear of the DVD-ROM drive.
2
Connecting the EIDE cable
• Insert the EIDE cable (40-pin), which is connected to the hard
disk to the interface terminal.
(Place the red line of the cable close to the Pin 1.)
3 Installing a jumper on the master/slave select termina
• Connect a jumper to the rear side of the DVD-ROM.
If the jumper is connected to MA (Master), it will work in the Master mode.
If the jumper is connected to SL (Slave), it will work in the Slave mode.
If the jumper is connected to CS (CSEL), you can control the device by using th
host interface signal CSEL. (In general, connection to MA is recommended.)
CS : Cable Select(CSEL)
SL : Slave
MA: Master
4 Connecting the EIDE cable from a sound card
• Connect the 4-pin audio cable between the sound output terminal on the
DVD-ROM drive and the audio input terminal on the sound card.
4
Technical Specifications
SH-D162D(TS-H352D)
SECTIONS
CD DVD
CD-DA(Audio), CD-ROM, CD-R, CD-RW, Photo-CD
(Single, Multi-session), Video CD ready, Enhanced CD, CD-I/FMV,
Disc types supported
DISC
CD-TEXT,CD-Plus, DVD-ROM, DVD-VIDEO, DVD+R, DVD-R,
DVD+RW, DVD-RW, DVD-RAM, DVD+R/-R Dual
Disc diameter 120mm or 80mm
Data transfer rate
Sustained Max. 21,600KB/sec(16X) Max. 7,200KB/sec (48X)
PIO mode 4
16.6MB/sec
DMA mode 2 16.6MB/sec
UDMA mode 2
33.3MB/sec
Access time(RANDOM) 110ms (typical)
DRIVE
Data Buffer capacity 198KB
PERFORMANCE
Semiconductor laser
Laser
Slide mechanism Stepping motor
Spindle motor Brushless Sensorless DC motor
Load mechanism Tray. DC motor (Soft Eject). Horizontal/Vertical.
ERROR RATE 10 -15 Mode 1:10 -12, Mode 2:10 -9
Eject button Eject, Insert
FRONT PANEL
Indicator(LED)
BUSY
Required power 1.5A (rms)
Interface connector
ATAPI
REAR PANEL
Audio output Line out 0.7V ± 20% : 47kΩ
Jumper block Molex 70203 or other compatible models
Operations
OPERATING Temperature: 5~45°C Humidity: 10~80%
ENVIRONMENT
Storage Temperature: -25~60°C Humidity: 10~90%
Dimensions 148.2 (W) x 42 (H) x 170 (D) mm (including bezel)
GENERAL
Net weight 740 g
9