Sealey PTB104008 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using these units.

Locate the units in a suitable work area.

Keep the work area clean, uncluttered and ensure there is adequate lighting.

WARNING! Use the units on level and solid ground, preferably concrete.

Keep the units clean and tidy in accordance with good workshop practice.

Keep children and unauthorised persons away from the work area.

DO NOT use these units for any purpose other than that for which they are designed.

DO NOT use the units outdoors.

DO NOT place the units in a damp or wet location or an area where there is condensation.

DO NOT clean the units with any solvents which may damage the surfaces or the protective coating.

DO NOT move the units with the drawers out. To avoid tipping, open one drawer at a time and close and secure all drawers whilst moving.

DO NOT step on the drawers.

2. INTRODUCTION
• Heavy-duty welded steel construction for strength and durability.
• Choice of finish; textured powder coat or anti-finger-print stainless steel, both solvent and rust resistant.
• Ball bearing drawer runners (double sets on large drawers), provide superior performance and carry heavier loads.
• All drawers have full width sand blasted aluminium lift latch drawer pulls, making easy access while preventing inadvertent opening when being moved.
• Non-slip drawer liners supplied for all drawers.
• Heavy-duty Ø125mm castors on rollcabs; 2 swivel with toe brakes and 2 fixed.
• Heavy-duty exterior handles on chest and cabinets.
• Topchests feature gas struts on lids for easy opening.
• Rollcabs (except for stainless steel versions) supplied with 12mm PVC coated MDF worktop for use as a workbench when not used with a topchest.
• Integral locking system locks all drawers in each unit with the turn of a key; all supplied with 2 keys.
• Manufactured to the highest levels of construction to withstand the toughest of workshop/garage conditions.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . .PTB104008 . . . . . . . . . . . . . . . PTB105511
Overall size (WxDxH) mm: . . . . . . . . . . .1040 x 450 x 570 . . . . . . . . . . . 1055 x 460 x 1050
Full width drawer (x1): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 950 x 385 x 135
Medium drawer (x3):. . . . . . . . . . . . . . . .595 x 385 x 58 . . . . . . . . . . . . . 595 x 385 x 58
Medium 1/2 drawer(x3): . . . . . . . . . . . . .300 x 385 x 58 . . . . . . . . . . . . . 295 x 385 x 58
Large drawer (x1): . . . . . . . . . . . . . . . . .595 x 385 x 135 . . . . . . . . . . . . 595 x 385 x 135
Large 1/2 drawer (x1): . . . . . . . . . . . . . .300 x 385 x 135 . . . . . . . . . . . . 295 x 385 x 135
X Large drawer (x1):. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 595 x 385 x 210
X Large 1/2 drawer (x1):. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295 x 385 x 210
4. ASSEMBLY
4.1. These units are heavy, obtain the help of at least one other person before attempting to unpack them.
4.2. Install Handle (refer to fig.1).
4.2.1. Position the holes on the side of the rollcab and attach with the bolts provided. Tighten securely.
4.3. Install Wheels (Rollcabs) (refer to fig.2).
4.3.1. Carefully lay rollcab on its back, with a soft mat underneath for protection. Install the two braked casters on the same end as the handle.
4.3.2. Insert the carriage bolts through washers, then through the casters and into the bottom of the cabinet. Tighten securely.
4.3.3. Install the fixed wheels on the opposite end to the handle.
© Jack Sealey Limited
INSTRUCTIONS FOR:
TOPCHEST 8 DRAWER 1040MM,
ROLLCAB 11 DRAWER 1055MM HEAVY-DUTY
MODEL No's: PTB104008, PTB105511
Fig.1
Original Language Version
Fig.2
PTB104008, PTB10511 Issue: 1 - 30/10/14