HIKVISION DS-2CD883F-E Installation Manual
  1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Security Camera
  5. DS-2CD883F-E series
  6. Installation manual

HIKVISION DS-2CD883F-E Installation Manual

Hikvision network camera installation manual
Hide thumbs Also See for DS-2CD883F-E:
Table of Contents

Advertisement

Quick Links

See also: Operating Manual , User Manual

Network Camera

Installation Manual
V5.1.0
UD.6L0201A1219A01
Lo-Call 1890 866 900
www.cctvireland.ie
shop@cctvireland.ie

Advertisement

Table of Contents
loading

Related Manuals for HIKVISION DS-2CD883F-E

Summary of Contents for HIKVISION DS-2CD883F-E

  • Page 1: Network Camera

    Network Camera Installation Manual V5.1.0 UD.6L0201A1219A01 Lo-Call 1890 866 900 www.cctvireland.ie shop@cctvireland.ie...
  • Page 2 Installing instructions of all these variety of cameras are listed in this manual. Find the model of your camera in the following list. Model DS-2CD883F-E(W), DS-2CD855F-E, DS-2CD854F(WD)-E(W), DS-2CD853F-E(W), DS-2CD864F(WD)-E(W), DS-2CD863PF(NF)-E(W), Type I DS-2CD893PFWD(NFWD)-E(W), DS-2CD833F-E(W),...
  • Page 3 Installation Manual of Network Camera Type IV DS-2CD2212-I, DS-2CD2232-I Type V DS-2CD2612F-I(S), DS-2CD2632F-I(S) DS-2CD4212F-(I)(Z)(H)(S), DS-2CD4212FWD-(I)(Z)(H)(S) Type VI DS-2CD4224F-(I)(Z)(H)(S), DS-2CD4232FWD-(I)(Z)(H)(S) Type VII DS-2CD6412FWD-10, DS-2CD6412FWD-20 Turret Camera DS-2CD2312-I5, DS-2CD2332-I5 Type I DS-2CD8153F-E(I)(W), DS-2CD8133F-E(I)(W) Cube Type II DS-2CD8464F-E(I)(W), DS-2CD8433F-E(I)(W) Camera Type III DS-2CD2412F-I(W), DS-2CD2432F-I(W) This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice.

  • Page 4: Safety Instruction

    Installation Manual of Network Camera Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. The precaution measure is divided into ‘Warnings’ and ‘Cautions’: Warnings: Serious injury or death may be caused if any of these warnings are neglected. Cautions: Injury or equipment damage may be caused if any of these cautions are neglected.
  • Page 5 Installation Manual of Network Camera Cautions:  Make sure the power supply voltage is correct before using the camera.  Do not drop the camera or subject it to physical shock.  Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a bit of ethanol and wipe it gently.

  • Page 6: Table Of Contents

    Installation Manual of Network Camera Table of Contents Chapter 1 Introduction ..........................7 Applications ............................7 Preparations ............................7 Chapter 2 Box Camera Installation ......................9 Type I Box Camera ..........................9 2.1.1 Camera Description ......................... 9 2.1.2 Installation............................11 Type II Box Camera ...........................
  • Page 7 Installation Manual of Network Camera Chapter 4 Bullet Camera Installation ....................... 83 Type I Bullet Camera ......................... 83 4.1.1 Camera Description ........................83 4.1.2 Installation............................84 Type II Bullet Camera ........................85 4.2.1 Camera Description ........................85 4.2.2 Installation............................86 Type III Bullet Camera ........................

  • Page 8: Chapter 1 Introduction

    Installation Manual of Network Camera Chapter 1 Introduction The network camera is a kind of embedded digital surveillance product that combines the features of both traditional analog camera and the encoder. With a built-in video server, the network camera is capable of providing real-time video stream compression, processing, video analysis and transmission simultaneously.
  • Page 9 Installation Manual of Network Camera  Make sure that there is no reflective surface too close to the camera lens. The IR light from the camera may reflect back into the lens causing reflection.  The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS.

  • Page 10: Chapter 2 Box Camera Installation

    Installation Manual of Network Camera Chapter 2 Box Camera Installation 2.1 Type I Box Camera 2.1.1 Camera Description The overview of Type I box camera is shown below: Figure 2-1 Overview Table 2-1 Description Description Lens Mount Back Focus Ring SD Card Slot Auto-iris Interface 10M/100M Self-adaptive Ethernet Interface...
  • Page 11 Installation Manual of Network Camera Description IN, G: Alarm Input Interface 1A, 1B: Alarm Output Interface Grounding RESET: Reset Button Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. The type of auto-iris interface is shown as below figure: Figure 2-2 Auto-iris Interface Table 2-2 Pins...

  • Page 12: Installation

    Installation Manual of Network Camera 2.1.2 Installation Steps: 1. Fix the mounting bracket to the ceiling. Expansion Screw Figure 2-3 Fix Camera Mounting Bracket 2. Aim the screw hole on the camera at the bracket and rotate the camera tightly. 3.

  • Page 13: Type Ii Box Camera

    Installation Manual of Network Camera 2). Adjust the lens focus to obtain a perfect image on the monitor. Figure 2-5 Install the Lens 2.2 Type II Box Camera 2.2.1 Camera Description The overview of Type II box camera is shown below: Figure 2-6 Overview (1) The overview of the components and the interface are shown below: Figure 2-7 Overview (2)
  • Page 14 Installation Manual of Network Camera The interfaces on the rear panel are shown below: Figure 2-8 Overview (3) Table 2-3 Description Description Description Lens Mount ¼-20 UNC Screw Hole Status Indicator Auto-iris Interface LAN(PoE) Power Outlet Reset Micro SD Card Slot Video Out Grounding Alarm Out...

  • Page 15: Installation

    Installation Manual of Network Camera The type of auto-iris interface is shown as below figure: Figure 2-9 Auto-iris Interface Table 2-4 Pins DC-driven Damp- Damp+ Drive+ Drive- Power, Video and GND pins are used when the auto-iris is driven by video; Damp+, Damp-, Drive+ and Drive- pins are used when the auto-iris is driven by DC.
  • Page 16 Installation Manual of Network Camera Adjustable Nut Figure 2-10 Install the Mount 2. Fit the lens (not supplied) to the camera and rotate it to get it tightened. ● Install the adapter ring to the lens interface if a C-mount lens is used. ●...

  • Page 17: Wall Mounting

    Installation Manual of Network Camera 2). Loosen the knob on the ceiling mount to adjust the tilt angle [0° -90]. 6. Adjust the Lens 1). Connect the VIDEO OUT interface of the camera to the debugging monitor. 2). Adjust the Zoom Lever and Focus Lever to obtain a perfect image on the monitor. Knob Figure 2-12 Install the Camera to the Mount and Adjust the Angle ...
  • Page 18 Installation Manual of Network Camera Tilt Adjust Table Lock Screw Figure 2-14 Remove the Tilt Adjust Table 4. Fit the removed tilt adjust table to the camera, and fix it with two screws. Figure 2-15 Install the Tilt Adjust Table 5.
  • Page 19 Installation Manual of Network Camera 1). Loosen the pan nut to adjust the pan angle [0 ° -360° ]. 2). Loosen the knob on the ceiling mount to adjust the tilt angle [0° -± 45° ]. 8. Adjust the Lens 1).

  • Page 20: Chapter 3 Dome Camera Installation

    Installation Manual of Network Camera Chapter 3 Dome Camera Installation 3.1 Type I Dome Camera 3.1.1 Camera Description Figure 3-1 Overview Table 3-1 Description Description 10M/100M self-adaptive Ethernet interface Reset Button AUDIO OUT: Audio output interface MIC IN: Audio input interface D+, D-: RS-485 interface 1A, 1B, 2A, 2B: Alarm output interface IN1, GND, IN2, GND: Alarm input interface...

  • Page 21: Installation

    Installation Manual of Network Camera 3.1.2 Installation  Ceiling Mounting Steps: Optional) use a plier to remove one clip or both two clips (marked in dotted line in Figure 3-2) on the side of the back box and then route cables through the opening to secure the cables on the ceiling.
  • Page 22 Installation Manual of Network Camera Figure 3-4 Mounting 4. Loosen the set screws with the hex key (supplied) to remove the bubble. Figure 3-5 Disassembling 5. Connect the RCA analog video output with a monitor to view the image of the camera. Loosen the lens set screw to adjust the angle of pan, tilt and rotation direction.
  • Page 23 Installation Manual of Network Camera Figure 3-7 Image Adjusting 7. Reinstall the bubble and tighten the screws Figure 3-8 Reinstall  In-ceiling mounting Steps: 1. Secure the mounting base to the in-ceiling mounting base with screws. Lo-Call 1890 866 900 www.cctvireland.ie shop@cctvireland.ie...
  • Page 24 Installation Manual of Network Camera In-ceiling Mounting base Mounting Base Figure 3-9 Mounting Base 2. Push the dome camera to the in-ceiling mounting base, rotate the dome camera for 10 degrees counterclockwise and then fasten the lock screws to fix the camera. ①...
  • Page 25 Installation Manual of Network Camera Figure 3-11 Installing 4. It is strongly recommended that you use a safety rope to secure the in-ceiling mounting base to the roof. Safety Rope Figure 3-12 Safety Rope 5. Fasten the lock screws to secure the dome camera. Lock Screw Figure 3-13 Fasten Screws Lo-Call 1890 866 900...
  • Page 26 Installation Manual of Network Camera 6. Remove the bubble and connect the RCA analog video output with a monitor to view the image of the camera. Loosen the lens set screw and pan, tilt or rotate the lens to get a desired surveillance angle.

  • Page 27: Type Ii Dome Camera

    Installation Manual of Network Camera 3.2 Type II Dome Camera 3.2.3 Camera Description Figure 3-16 Overview Table 3-2 Physical Description Description Cover Lens Power LED indicator, It turns solid red when power is connected. Base plate Set screw hole Set screw of lens S &...

  • Page 28: Installation

    Installation Manual of Network Camera 3.2.4 Installation Steps: 1. (Optional) Use a plier to remove the clip (marked in dotted line in 0) on the side of the back box and then route the cables through the opening instead of the cable hole. Figure 3-17 Side Clip 2.
  • Page 29 Installation Manual of Network Camera Figure 3-19 Fix the Camera 4. View the video image of the camera over the network. 5. Loosen the lens set screws. Figure 3-20 Loosen the Lens Set Screws 6. Insert the hex key into the hole marked in the picture and rotate the hex key to adjust the panning position and tilting position until getting the desired surveillance angle.
  • Page 30 Installation Manual of Network Camera Figure 3-21 Adjust Panning Position Figure 3-22 Adjust Tilting Position As the lens of camera has already been factory adjusted to the best imaging effect, you just need to adjust the panning position and tilting position to get the desired surveillance angle. 7.

  • Page 31: Type Iii Dome Camera

    Installation Manual of Network Camera Figure 3-23 Install the Back Box 3.3 Type III Dome Camera 3.3.1 Camera Description Figure 3-24 Overview Lo-Call 1890 866 900 www.cctvireland.ie shop@cctvireland.ie...

  • Page 32: Installation

    Installation Manual of Network Camera Table 3-3 Description Description Ceiling Mount Lock Button Mounting Base SD Card Slot Lens IR LED Bubble Status Indicator RCA Analog Video Output Debug Reset Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
  • Page 33 Installation Manual of Network Camera Figure 3-25 Drill Template 2. Fix the ceiling mount to the ceiling with screws. Ceiling Ceiling Mount Figure 3-26 Fix the Ceiling Mount 3. Route the cables through the cable hole on the ceiling. If required, you can rotate the side outlet on the mounting base to remove it and route the cables through the side outlet.
  • Page 34 Installation Manual of Network Camera Side Outlet Figure 3-27 Side Outlet 4. Insert the three screws on the mounting base into the corresponding holes on the ceiling mount. 5. Rotate the mounting base clockwise to secure the dome camera to the ceiling mount. Hole Screw Unlock Button...
  • Page 35 Installation Manual of Network Camera Figure 3-29 Uninstall the Dome Camera 6. Loosen the set screws with a hex key (supplied) to remove the bubble. Figure 3-30 Remove the Bubble 7. Connect the RCA analog video output with a monitor to view the image. 8.
  • Page 36 Installation Manual of Network Camera RCA Analog Video Output for Test Set Screw Zoom Puller Focus Puller Figure 3-31 Image Adjusting 10. Reinstall the bubble and tighten the screws to complete the installation. Figure 3-32 Reinstallation Lo-Call 1890 866 900 www.cctvireland.ie shop@cctvireland.ie...

  • Page 37: Type Iv Dome Camera

    Installation Manual of Network Camera 3.4 Type IV Dome Camera 3.4.1 Camera Description 2 3 4 Figure 3-33 Overview Table 3-4 Physical Description Description Video output interface LINK: Indicator is solid yellow when network is connected. ACT: Indicator flashes blue when network connection is functioning properly.

  • Page 38: Installation

    Installation Manual of Network Camera  Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. 3.4.2 Installation  Ceiling Mounting Steps: 1. Drill the screw holes on the ceiling with the supplied drilling template. If you need to route the cables from the bottom of the camera, cut a cable hole in the ceiling.
  • Page 39 Installation Manual of Network Camera Figure 3-36 Disassembling 4. Install the dome drive to the back box and pull the cables through the cable outlet on the bottom of the back box. Figure 3-37 Dome Drive Installing If you need to pull the cable through the side outlet of the camera, please remove the cover and use water-proof joints and water-proof pipe to route the cables.
  • Page 40 Installation Manual of Network Camera Outlet Figure 3-38 Side Cable Routing 5. After connecting the network cable and power cable, view the image of the camera over the network. Loosen the lock screws; adjust the panning position and tilting position and rotate the lens to get the desired surveillance angle;...
  • Page 41 Installation Manual of Network Camera  In-ceiling Mounting: Steps: 1. Drill the screw holes and the cable hole on the ceiling according to the supplied drill template. Drill Template Hole A: for the recessed part of the camera body Screw hole 1: for Toggle bolt Code:190600840 Figure 3-41 Drill Template 2.
  • Page 42 Installation Manual of Network Camera Toggle Bolt Figure 3-43 Dome Drive Installing 6. Fasten the toggle bolt and the toggle will automatically secure the dome drive to the ceiling. Ceiling Figure 3-44 Fasten Toggle Bolt 7. Connecting the network cable and power cable. 8.
  • Page 43 Installation Manual of Network Camera Tilt Lock Screw Rotate Figure 3-45 Angle Adjusting 11. Reinstall the black liner and dome drive to finish the installation. Figure 3-46 Complete the Installation Lo-Call 1890 866 900 www.cctvireland.ie shop@cctvireland.ie...
  • Page 44 Installation Manual of Network Camera  Wall mounting: Steps: 1. Drill the screw holes and the cable hole on the wall according to the supplied drill template. Drill Template Hole A: for cables routed Screw hole 3: for through the ceiling Mounting Base Code:190600839 Figure 3-47 Drilling Template...
  • Page 45 Installation Manual of Network Camera Figure 3-49 Disassembling 4. Install the dome drive to the back box and pull the cables through the side outlet on the bottom of the back box. If you need to pull the cable through the cable outlet from the side of the camera, please remove the cover and use water-proof joints and water-proof pipe to route the cables.
  • Page 46 Installation Manual of Network Camera 6. View the camera image over the network. 7. Loosen the lock screws to adjust the panning position and tilting position, and rotate the lens to get the desired surveillance angle. 8. Fasten the lock screws. Lock Screw Tilt Rotate...

  • Page 47: Type V Dome Camera

    Installation Manual of Network Camera 3.5 Type V Dome Camera 3.5.1 Camera Description Figure 3-53 Overview Table 3-5 Description Description Mounting Base Horizontal Stand Vertical Stand Bubble Power/Network Cables IR LED Lens Black Liner Safety Rope Press RESET button about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.

  • Page 48: Installation

    Installation Manual of Network Camera 3.5.2 Installation Steps: 1. Drill the screw holes on the ceiling according to the drill template. Screw Hole Ceiling Mounting Screw Hole Screw Hole Figure 3-54 Drilling Template 2. Loosen the set screws with a hex key (supplied) to remove the bubble. Figure 3-55 Remove the Bubble 3.
  • Page 49 Installation Manual of Network Camera Figure 3-56 Fix the Mounting Base If required, you can route cables through the side opening on the side of the mounting base. Side Opening Figure 3-57 Side Opening 4. Loosen the tilt lock screws, adjust the tilting position in a range of 65 degrees, and tighten the tilt lock screws.

  • Page 50: Type Vi Dome Camera

    Installation Manual of Network Camera As the lens has already been factory adjusted to the best imaging effect, you just need to adjust the panning position and tilting position to get the desired surveillance angle. 6. Reinstall the bubble and tighten the screws. Figure 3-59 Bubble Reinstallation 3.6 Type VI Dome Camera 3.6.1 Camera Description...
  • Page 51 Installation Manual of Network Camera Figure 3-60 Overview Table 3-6 Overview Description Bubble Black Liner Lens Mounting Base Reset Auxiliary Video Output Serial Port Micro SD Card Slot Network Cable Power Cable Audio/Alarm Interface Lo-Call 1890 866 900 www.cctvireland.ie shop@cctvireland.ie...

  • Page 52: Installation

    Installation Manual of Network Camera  Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.  The DS-2CD2712F-IS and DS-2CD2732F-IS models support audio and alarm functions. The interfaces are shown as follows.
  • Page 53 Installation Manual of Network Camera Screw Hole Black Liner Bubble Figure 3-62 Remove the Bubble and Black Liner 3. Attach the drill template (supplied) to the place where you want to fix the camera. 4. According to the drill template as shown below, drill three screw holes in the ceiling. Side Cable Outlet Cable Outlet Drilling Template for Outdoor...
  • Page 54 Installation Manual of Network Camera Back Box Screw Figure 3-64 Secure the Camera 8. Route the cables through the cable hole. 9. Connect the video output connector to the monitor. Connect the power connector to the power supply. 10. Adjust the image and focus. Please refer to Image and Focus and Adjusting for more detailed information.
  • Page 55 Installation Manual of Network Camera Water-proof Plug Side Cable Outlet Figure 3-66 Remove the water-proof plug 2. Route the power cable and network cable through the side outlet to the conduit. 3. Align and rotate clockwise the conduit to the side outlet tightly. Conduit Figure 3-67 Install the Conduit to the Camera For wall mounting, position the side outlet directly downward for water-proof.

  • Page 56: Ceiling Mounting With Gang Box

    Installation Manual of Network Camera  Ceiling Mounting With Gang Box Steps: 1. Disassemble the camera. 2. Install the gang box in the ceiling. 3. Attach the mounting base to the gang box with two screws. Mounting Base Figure 3-69 In-ceiling Mount 4.
  • Page 57 Installation Manual of Network Camera 9. Install the inner black liner back to the camera. 10. Align the bubble with the camera. 11. Tighten the screws to secure the bubble with the camera as shown below. Figure 3-71 Secure the Bubble ...
  • Page 58 Installation Manual of Network Camera 5. Route the cables through the hole in the center of the wall mount. 6. Align the camera with the mounting base. 7. Tighten the set screws to secure the camera with the mounting base. 8.

  • Page 59: Image And Focus Adjusting

    Installation Manual of Network Camera  Image and Focus Adjusting Steps: 1. View the camera image using the monitor. 2. Rotate the panning table to adjust the panning position of the camera. 3. Rotate the tilting axes to adjust the tilting position of the camera. 4.

  • Page 60: Type Vii Dome Camera

    Installation Manual of Network Camera 3.7 Type VII Dome Camera 3.7.1 Camera Description The overview of the dome camera is shown below: Figure 3-77 Overview The overview of the components and the interface are shown below: Figure 3-78 Overview (2) The interfaces on the rear panel are shown below: Lo-Call 1890 866 900 www.cctvireland.ie...
  • Page 61 Installation Manual of Network Camera Figure 3-79 Overview (3) Figure 3-80 Overview (4) Table 3-7 Description of Overview (2~3) Description Description Black Liner Bubble Lens BNC Interface Reset Status Indicator Test Serial Port Micro SD Card Slot Adapter Plate Side Outlet Table 3-8 Description of Overview (4) Lo-Call 1890 866 900 www.cctvireland.ie...

  • Page 62: Installation

    Installation Manual of Network Camera Name Description 10M/100M Self-adaptive Ethernet Port(PoE LAN（PoE） Supported) AUDIO OUT/IN Audio Out/In CVBS，GND Auxiliary video output 1A，1B Alarm Out D+，D- RS-485 Interface IN，GND ALARM IN Power Supply Interface（12 VDC ） DC12V Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
  • Page 63 Installation Manual of Network Camera Side Outlet Figure 3-82 Side Outlet 2. Fix the adapter plate to the ceiling with the supplied screws. Figure 3-83 Install the Adapter Plate 3. Align the mounting base with the adapter plate and route the mounting base anticlockwise to get it fitted with the adapter plate, and then fix it by tightening the lock screw.
  • Page 64 Installation Manual of Network Camera 4. Adjust the surveillance angle according to the figure below. Panning angle [0~80° ], tilting angle [0~355° ], and azimuth angle of the lens [0~355° ]. 0~80° 0~355° 0~355° Figure 3-85 3-axis Adjustment 5. Adjust the focus and zoom. 1).
  • Page 65 Installation Manual of Network Camera For the camera adopts electronic lens, you can adjust the zoom and focus by visiting the device, and adjust it from the PTZ control interface. Figure 3-87 Zoom and Focus Adjustment of Electronic Lens 6. Attach the black liner to the dome drive. 7.

  • Page 66: Type Viii Dome Camera

    Installation Manual of Network Camera 3.8 Type VIII Dome Camera 3.8.1 Camera Description of Type A Dome Camera The overview of the outdoor dome camera is shown below: Figure 3-90 Overview (1) Figure 3-91 Overview (2) Table 3-9 Description of Overview (1~2) Description Description Black Liner...

  • Page 67: Installation Of Type A Dome Camera

    Installation Manual of Network Camera 10/100M Self-adaptive Mounting Base Ethernet Interface SD Card Slot Lens Video Out Audio and Alarm Cables 3.8.2 Installation of Type A Dome Camera Steps: 1. Drill the screw holes and the cable hole according to the supplied drill template. Drill Tempalte Hole A: for cables routed Screw Hole 3: for...
  • Page 68 Installation Manual of Network Camera 3. Connect the corresponding power cable, network cable, audio and alarm cables. 4. Install the dome drive to the mounting base. Dome Drive Figure 3-94 Install the Dome Drive 5. Adjust the surveillance angle. 1). Loosen the lock screw besides the lens. 2).
  • Page 69 Installation Manual of Network Camera 1). Connect the VIDEO OUT interface of the camera to the debugging monitor. 2). Set the iris type to MANUAL first. 3). Adjust the No.2 Zoom Lever (T~W) to select a proper angle of view. 4).

  • Page 70: Camera Description Of Type B Dome Camera

    Installation Manual of Network Camera 3.8.3 Camera Description of Type B Dome Camera Figure 3-98 Overview of Type B Dome Camera Table 3-10 Description of Type B Dome Camera Description Description 10/100M Self-adaptive Bubble Ethernet Interface SD Card Slot Lens Video Out Interface Audio/Alarm Cables Reset...
  • Page 71 Installation Manual of Network Camera 1. Drill the screw holes and the cable hole according to the supplied drill template. Drill Tempalte Hole A: for cables routed Screw Hole 3: for through the ceiling Mounting Base Code: 190600839 Figure 3-99 Drill Template 2.
  • Page 72 Installation Manual of Network Camera Figure 3-101 Install the Dome Drive The surveillance angle of the camera is well- adjusted by default. If the pan and tilt angle is required to adjusted according to the different installation environment, go to the live view interface via web browser or client software after the installation is completed.

  • Page 73: Type Ix Dome Camera

    Installation Manual of Network Camera 3.9 Type IX Dome Camera 3.9.1 Camera Description Figure 3-104 Overview (1) Figure 3-105 Overview (2) Table 3-11 Physical Description Description Front Cover Dome Drive Micro SD Card Slot Network Cable Lens Lo-Call 1890 866 900 www.cctvireland.ie shop@cctvireland.ie...

  • Page 74: Installation

    Installation Manual of Network Camera Description IR LED Power Cable Audio/Alarm Cables Wi-Fi Antenna Serial Port Interface Hex Screw RESET/WPS Button  Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. No.8 is the audio/alarm cable interface, of which the “I”...
  • Page 75 Installation Manual of Network Camera Drill Template Hole A:for cables routed through the ceiling Screw hole 1:for Mounting Base FRONT Figure 3-106 Type I Drill Template A different type of drill template might be provided because of the different batches of products. And also, the contained adapter plate matches with type II drill template differs as well.
  • Page 76 Installation Manual of Network Camera Figure 3-108 Disassemble the Camera 3. Fix the adapter plate to the ceiling with the supplied expansion screws. Adapter Plate Side Outlet Figure 3-109 Fix the Adapter Plate If the supplied drill template is type II drill template, you can skip step 3 and go straight to step 4. 4.
  • Page 77 Installation Manual of Network Camera Figure 3-110 Fix the Dome Drive 5. Connect the power cable, network cable, and the alarm/audio cable. Use a plier to remove the removable part and route the cables via side outlet (as shown in Figure 3-109) if no cable hole is drilled in step 1, and connect the corresponding cables.
  • Page 78 Installation Manual of Network Camera Adjusting Tool Rotation Tilt Figure 3-112 3-axis Adjustment 9. Tighten the hex screw to fix the well-adjusted surveillance angle. 10. Align the front cover to the dome drive and tighten the set screws on the front cover to complete the installation.
  • Page 79 Installation Manual of Network Camera 2. Fix the dome drive to the adapter plate with the supplied PM4x8 screws. Figure 3-115 Fix the Dome Drive 3. Connect the power cable, network cable, and the alarm/audio cables. 4. Align the front cover to the dome drive and tighten the set screws on the front cover to complete the installation.
  • Page 80 Installation Manual of Network Camera Figure 3-117 Fix the Adapter Plate 3. Install the dome drive to the adapter plate. Figure 3-118 Fix the Dome Drive 4. Align the front cover to the dome drive and tighten the set screws on the front cover to complete the installation.
  • Page 81 Installation Manual of Network Camera Figure 3-119 Install the Front Cover  Wall Bracket Mounting Steps: 1. Install the wall bracket to the wall with the supplied screws in the wall bracket package. The matched ceiling bracket model is DS-1272ZJ-120B, and you need to purchases it separately if wall bracket mounting is adopted.
  • Page 82 Installation Manual of Network Camera Figure 3-121 Fix the Adapter Plate 3. Fix the dome drive to the wall bracket with the supplied screws. Figure 3-122 Fix the Camera 4. Align the front cover to the dome drive and tighten the set screws on the front cover to complete the installation.
  • Page 83 Installation Manual of Network Camera Steps: 1. Remove the front cover by loosening the set screws on it. Figure 3-124 Remove the Front Cover 2. Insert the micro SD card to the card slot until you hear a click. 3. (Optional)Slightly push the inserted micro SD card to uninstall it from the camera. Mirco SD Card Figure 3-125 Install and Uninstall Micro SD Card Lo-Call 1890 866 900...

  • Page 84: Chapter 4 Bullet Camera Installation

    Installation Manual of Network Camera Chapter 4 Bullet Camera Installation 4.1 Type I Bullet Camera 4.1.1 Camera Description The camera overview is shown as follows: Figure 4-1 Overview Figure 4-2 Overview Table 4-1 Description Description 10M/100M self-adaptive Ethernet interface Power Supply Sun Shield Adjusting Screw Lo-Call 1890 866 900...

  • Page 85: Installation

    Installation Manual of Network Camera 4.1.2 Installation Steps: 1. Attach the wall mount (not provided) to the wall and tighten the screws to fix it. Figure 4-3 Install the Wall Mount 2. Secure the camera to the wall mount with set screws. 3.

  • Page 86: Type Ii Bullet Camera

    Installation Manual of Network Camera 5. Loosen the tilting lock screw to adjust the tilting angle [0~90° ]. Figure 4-6 Tilting 4.2 Type II Bullet Camera 4.2.1 Camera Description Two types of camera rear panel are shown in Figure 4-7 and Figure 4-8. Choose the right figure according to your purchased product.

  • Page 87: Installation

    Installation Manual of Network Camera Table 4-2 Physical Description Description 10M/100M Self-adaptive Ethernet Interface Power Supply Interface IN, G: Alarm input interface 1A, 1B: Alarm output interface D+, D-: RS-485 interface AUDIO IN, G: Audio input interface AUDIO OUT, G: Audio output interface 4.2.2 Installation Steps: 1.
  • Page 88 Installation Manual of Network Camera Figure 4-10 Fix the Camera 3. View the image of the camera over the network. 4. Loosen the screws on the bracket slightly. Please loosen the screws slightly until you can adjust the camera and do not remove the screws from the bracket.
  • Page 89 Installation Manual of Network Camera Figure 4-12 Remove the Sun Shield 7. Rotate to remove the front cover from camera and adjust the lens to get a clear image. Adjust the Lens Front Cover Figure 4-13 Adjust the Lens 8. Fix the lens; reinstall the front cover and the sun shield to finish the installation. Figure 4-14 Complete the Installation Lo-Call 1890 866 900 www.cctvireland.ie...

  • Page 90: Type Iii Bullet Camera

    Installation Manual of Network Camera 4.3 Type III Bullet Camera 4.3.1 Camera Description Figure 4-15 Bullet Camera Overview Table 4-3 Description Description Sun Shield Back Box Grounding Screw Adjustable Bracket Mounting Base Reset 4.3.2 Installation Steps: 1. Attach the drill template on the wall. Lo-Call 1890 866 900 www.cctvireland.ie shop@cctvireland.ie...
  • Page 91 Installation Manual of Network Camera Screw Hole Template Figure 4-16 Attach the template 2. Secure the camera to the ceiling with the supplied expansion screws. Figure 4-17 Secure the Camera to the Ceiling 3. Adjust the Lens. Loosen the adjustable nut on the bracket. Adjust the panning angle [0~360°...

  • Page 92: Type Iv Bullet Camera

    Installation Manual of Network Camera T Direction R Direction P Direction Adjustable Figure 4-18 3-axis Adjustment 4.4 Type IV Bullet Camera 4.4.1 Camera Description Figure 4-19 Bullet Camera Overview Table 4-4 Description Description Lens IR LED Sun Shield Adjusting Screw Network Cable Power Cable Lo-Call 1890 866 900...

  • Page 93: Installation

    Installation Manual of Network Camera 4.4.2 Installation Steps: 1. Drill the cable hole and the screw hole in the ceiling according to the supplied drill template. Ceiling Mounting 1:Screw Hole for 2:Screw Hole for Bracket Mounting Base Figure 4-20 The Drill Template 2.

  • Page 94: Type V Bullet Camera

    Installation Manual of Network Camera 4). Tighten No.2 adjusting screw. 5). Loosen No.3 adjusting screw to adjust the azimuth angle [0° ~ 360° ]. 6). Tighten No.3 adjusting screw. Figure 4-22 3-axis Adjustment 4.5 Type V Bullet Camera 4.5.1 Camera Description The overview of the network bullet camera is shown below.

  • Page 95: Installation

    Installation Manual of Network Camera Description Sun Shield Front Cover Zoom and Focus Lever IR LED Lens Air Vent Video Output Interface Integrated Bracket Reset Button Micro SD Card Slot Power Interface Network Interface  Press RESET button about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
  • Page 96 Installation Manual of Network Camera 2. Remove the sun shield according to the arrow direction as shown in Figure 4-25 (right). 3. Remove the front cover by rotating it counterclockwise as shown in Figure 4-25 (right). Lock Screw Figure 4-25 Disassemble the Camera 4.
  • Page 97 Installation Manual of Network Camera Rotating Label Figure 4-27 Assemble the Camera For water-proof, please align the rotating label on the front cover with that on the camera when you rotate the front cover clockwise. Refer to Figure 4-27 (right). ...
  • Page 98 Installation Manual of Network Camera Figure 4-29 Secure the Camera  Wall Mounting with a Junction Box Before you start: For mounting with a junction box, you have to purchase a junction box. Steps: 1. Attach the drill template (supplied) to the wall where the camera is to be mounted. 2.
  • Page 99 Installation Manual of Network Camera Junction Box Safety Rope Figure 4-30 Secure the Camera  Wall Mounting with a Gang Box Before you start: For mounting with a gang box, you have to purchase a gang box. Steps: 1. Secure the camera attachment to a gang box with screws. 2.
  • Page 100 Installation Manual of Network Camera 1. Loosen the lock screw-1. 2. Adjust the panning position of the camera. The adjusting range is from 0 degrees to 360 degrees. 3. Tighten the lock screw-1. Tilt Adjustment Steps: 1. Loosen the lock screw-2. 2.

  • Page 101: Type Vi Bullet Camera

    Installation Manual of Network Camera 5. Loosen the focus lever and move the screw between F (Far) and N (Near) to obtain the optimum focus. 6. Tighten the focus lever. 7. Assemble the camera. Zoom/Focus Lever Figure 4-33 Zoom and Focus Adjustment 4.6 Type VI Bullet Camera 4.6.1 Camera Description The overview of the network bullet camera is shown below:...

  • Page 102: Installation

    Installation Manual of Network Camera Table 4-6 Description Description Description Sun Shield Bracket Junction Box Reset SD Card Slot Front Box Analog Video Output 4.6.2 Installation Steps: 1. Drill four screw holes in the wall according to the No.2 holes of the supplied drill template. Cable Hole Figure 4-35 Drill Template 2.
  • Page 103 Installation Manual of Network Camera Junction Box Figure 4-36 Install the Junction Box 4. Route the cables of the camera. ● Route the cables through the junction box and the cable hole if there is a cable hole drilled on the ceiling. ●...
  • Page 104 Installation Manual of Network Camera Pan Adjust Nut Tilt Adjust Nut Figure 4-38 Adjust Monitoring Angle  Please loosen the screws slightly until you can adjust the camera and do not remove the screws from the bracket.  After the monitoring angle is adjusted, you may need to install a water-proof rubber case (purchased separately) to the foldable position of the bracket to protect it from water.

  • Page 105: Type Vii Bullet Camera

    Installation Manual of Network Camera Figure 4-40 Installation Complete 4.7 Type VII Bullet Camera 4.7.1 Camera Description 13 14 9 10 11 VIN1 AUDIO AUDIO LAN(PoE) RXD TXD GND IN1 1B 1A DC 12V RESET 16 17 Figure 4-41 The Overview of Covert Camera with Cylindrical Sensor Unit Lo-Call 1890 866 900 www.cctvireland.ie shop@cctvireland.ie...
  • Page 106 Installation Manual of Network Camera 13 14 9 10 11 VIN1 AUDIO AUDIO LAN(PoE) RXD TXD GND IN1 1B 1A DC 12V RESET 16 17 Figure 4-42 The Overview of Covert Camera with Block-shaped Sensor Unit Table 4-7 Description of the Camera Description Description Main Unit...

  • Page 107: Installation

    Installation Manual of Network Camera Color& Status Indicator Solid green Camera works properly STATUS Unlit Camera does not work properly. Flashing amber Network connection is functioning properly LINK Unlit No network connection 4.7.2 Installation  Installation of Main Unit Steps: 1.
  • Page 108 Installation Manual of Network Camera Figure 4-44 Buckle the Main Unit If you already had a standard rail to be installed, you can buckle the main unit onto the installed rail directly. Figure 4-45 Buckle the Main Unit onto Standard Rail ...
  • Page 109 Installation Manual of Network Camera Figure 4-46 Drill on the Surface Make sure the drilling hole is big enough for the camera lens. 2. Remove a side of the adhesive tape on the bracket. Paste the bracket on the mounting surface with aligning with the drilling hole.
  • Page 110 Installation Manual of Network Camera Figure 4-48 Insert the Block-shaped Sensor Unit  Exposed Mounting Steps: 1. Fix the Block-shaped sensor unit on the mounting surface with screws. As shown in Figure 4-49. Figure 4-49 Fix the Block-shaped Sensor Unit ●...
  • Page 111 Installation Manual of Network Camera Figure 4-50 Hood the Cover  Installation of Cylindrical Sensor Unit This series of camera only support concealed mounting. Please make sure that the mounting surface is suitable for adhesive pasting. Steps: 1. Drill on the mounting surface. As shown in Figure 4-51. Figure 4-51 Drill on the Surface Make sure that the drilling hole is big enough for the camera lens.
  • Page 112 Installation Manual of Network Camera Figure 4-52 Paste the Bracket 3. Install the cylindrical sensor into the mounting hole in the round rail bracket. 4. Turn the locking sleeve to fix the sensor. As shown in Figure 4-53. Figure 4-53 Install the Cylindrical Sensor Lo-Call 1890 866 900 www.cctvireland.ie shop@cctvireland.ie...

  • Page 113: Chapter 5 Turret Camera Installation

    Installation Manual of Network Camera Chapter 5 Turret Camera Installation 5.1 Camera Description Figure 5-1 Overview Table 5-1 Description Description 10M/100M self-adaptive Ethernet interface Power Cable Trim Ring Lens IR LED Enclosure Dome Drive Please make sure that the power adapter is compatible with the camera. This series of camera supports Power over Ethernet (PoE), and the standard power supply is 12 VDC.
  • Page 114 Installation Manual of Network Camera Trim Ring Dome Drive Figure 5-2 Dissemble the Camera 2. Drill the screw holes and the cable hole on the ceiling according to the drill template. Figure 5-3 The Drill Template There are two cable outlet methods. One is to route the cables through the cable hole, and the other is to route the cables through the side outlet shown below.
  • Page 115 Installation Manual of Network Camera Three side outlets on the enclosure are selectable, which makes routing the cables easier instead of drilling a cable hole on the ceiling. Use a plier to remove the plastic and route the cables through the hole.
  • Page 116 Installation Manual of Network Camera Figure 5-7 Adjust the Lens 6. Attach the trim ring to the camera and rotate the trim ring clockwise to get it secured. Figure 5-8 Install the Trim Ring Lo-Call 1890 866 900 www.cctvireland.ie shop@cctvireland.ie...
  • Page 117 Installation Manual of Network Camera Figure 5-9 Complete the Installation Lo-Call 1890 866 900 www.cctvireland.ie shop@cctvireland.ie...

  • Page 118: Chapter 6 Cube Camera Installation

    Installation Manual of Network Camera Chapter 6 Cube Camera Installation 6.1 Type I Cube Camera 6.1.1 Camera Description Figure 6-1 Overview Table 6-1 Description Description IR LED Microphone LINK: Network Status LED Indicator. LED indicator is solid yellow when network connection is functioning properly.

  • Page 119: Installation

    Installation Manual of Network Camera Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. 6.1.2 Installation Steps: 1. Fix the mounting bracket to the ceiling. Expansion Screw Self-tapping Screw Figure 6-2 Fix the Bracket...

  • Page 120: Type Ii Cube Camera

    Installation Manual of Network Camera 3. View the video image over the network. Loosen the knob on the bracket and adjust the camera lens to get the desired surveillance angle. Tighten the knob on bracket to secure the camera. Figure 6-4 Installation Completes 6.2 Type II Cube Camera 6.2.1 Camera Description The overview of the network cube camera is shown below.
  • Page 121 Installation Manual of Network Camera Figure 6-5 Overview Table 6-2 Description Description IR LED Photosensitive Resistance PIR sensor Microphone Lens 3-axis Adjustment Bracket Alarm Indicator: Indicator goes solid red (camera armed) or solid blue (camera unarmed). Status Indicator: Indicator flashes blue when any movement or presence is detected Link Indicator: Indicator flashes orange when network connection is functioning properly.

  • Page 122: Remote Control Overview

    Installation Manual of Network Camera 6.2.2 Remote Control Overview A remote control is included in the package to provide a convenient operation. Please refer to the figure below. Figure 6-6 Remote Control Table 6-3 Remote Control Button Description Button Name Description Status Indicating the status of the remote control;...
  • Page 123 Installation Manual of Network Camera Fixator Right Cover Figure 6-7 Remove the Cover and Fixator 2. Drill the screw holes and the cable hole according to the supplied drill template. Drill no cable hole if you intend to route the cables through the side outlet of the camera. 3.
  • Page 124 Installation Manual of Network Camera Side Outlet Figure 6-9 Reinstall the cover and Fixator 6. 3-axis Adjustment. View the image of the camera over the network. Loosen the lock nut 1 to adjust the panning position and tilting position. Fasten the lock nut 1. Loosen the lock nut 2 to rotate the camera.

  • Page 125: Type Iii Cube Camera

    Installation Manual of Network Camera 6.3 Type III Cube Camera 6.3.1 Camera Description Figure 6-11 Overview Table 6-4 Description Description Lens PIR(Passive Infrared) sensor Microphone Alarm: Solid red when the camera is armed; Solid blue when the camera is unarmed. Indicators Status: Reserved Link: Flashing amber when network is connected;...

  • Page 126: Notice

    Installation Manual of Network Camera  Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.  A wireless router with the WPS function is required to enable the WPS function of the camera. Refer the steps below.
  • Page 127 Installation Manual of Network Camera  Do not install the camera towards the Do not subject the camera  strong light or in the unstable to vibration, shock or heavy lightening condition. pressure.  High humidity may damage the  Under no circumstances should camera hardware;...

  • Page 128: Installation

    Installation Manual of Network Camera 6.3.3 Installation Steps: 1. Open the cover on the mounting base from the bracket. Figure 6-12 Open the Cover 2. Drill the screw holes according to the drill template. Figure 6-13 Drill Template Lo-Call 1890 866 900 www.cctvireland.ie shop@cctvireland.ie...
  • Page 129 Installation Manual of Network Camera 3. Use 3 screws to fix the bracket to the ceiling and the screw hole on the bracket should align with the mounting hole on the drill template. Figure 6-14 Fix the Bracket 4. Install the mounting base cover and attach the camera on the bracket. Figure 6-15 Install the Cover and Camera 5.
  • Page 130 Installation Manual of Network Camera Knob Figure 6-16 Adjust the Camera Lo-Call 1890 866 900 www.cctvireland.ie shop@cctvireland.ie...
  • Page 131 Lo-Call 1890 866 900 www.cctvireland.ie shop@cctvireland.ie...

This manual is also suitable for:

Ds-2cd854f-eDs-2cd855f-eDs-2cd854f-ewDs-2cd883f-ewDs-2cd864f-eDs-2cd854fwd-ew ... Show all

Table of Contents