Advertisement
Quick Links
Mitsubishi Installation
PROJECTOR COMMUNICATIONS KIT
PLEASE READ THIS DOCUMENT FOR IMPORTANT
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:
Kit Type: MITSUBISHI
Included Communications Adapter(s):
Quantity
1
1
1
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER'S VARIOUS
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS
INDICATED BY THE " " IN THE "CONFIG AS" COLUMN. IF YOUR PROJECTOR MODEL
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER
WITH THE CORRECT SETTINGS.
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND
SIGNAL CONNECTION INSTRUCTIONS.
THIS SWITCHER HAS BEEN CONFIGURED FOR:
CONFIG
MODEL
AS
VS
LVP-X100
LVP-X200X300 off on off on
LVP-X400
Extron • System 4 xi xi xi xi xi Switcher Series • User's Manual • P/N 68-401-02 Rev. C
SYSTEM 4xi xi xi xi xi
ATTENTION!
INSTALLATION INSTRUCTIONS
Part Number
26-473-01
26-475-01
26-458-01
SW1
SW2 SW3 SW4 SW5 SW6 PROJ
1
2
3
4
off on off on
0
off on off on
0
0
off on off on
0
Configuration and Connections
Description
ADP, UNV, "E"
ADP, UNV, "G"
ADP, UNV, "NEC-LCD MT"
MITSUBISHI VS
0
8
5
0
0
6
F
0
1
6
F
0
2
6
F
0
COMM
CABLE
ADAPTER
J15
26-473-01
J15
26-475-01
J15
26-475-01
J15
26-458-01
Page 1
Page 1
Advertisement
Related Manuals for Mitsubishi VS
Summary of Contents for Mitsubishi VS
-
Page 1: Installation Instructions
SYSTEM 4xi xi xi xi xi PROJECTOR COMMUNICATIONS KIT ATTENTION! PLEASE READ THIS DOCUMENT FOR IMPORTANT INSTALLATION INSTRUCTIONS THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS: Kit Type: MITSUBISHI Included Communications Adapter(s): Quantity Part Number Description 26-473-01 ADP, UNV, “E”... - Page 2 System 4xi ’s Main Controller Board. Begin at Step 1 to verify the correct configuration. 1. Use the Front Panel to display the Information Menu to verify that the System 4xi is already set up for the Mitsubishi LVP-X100. Apply power to the System 4xi and do the following: a. Press to display the M on the LCD screen.
- Page 3 7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV cable onto the System 4xi output. Connect the 15-pin connector on the other end of the RGBS/HV cable to the PC-1 Input connector on the Mitsubishi LVP-X100 connector panel.
- Page 4 Connecting System 4xi xi xi xi xi to Mitsubishi VS Projector If the System 4xi is already configured for a Mitsubishi VS Projector, go to step 4. If it is not set up correctly, it will be necessary to change switch settings on the System 4xi ’s Main Controller Board.
- Page 5 BNCs on the Mitsubishi VS projector connector panel. See connection diagram below. System 4xi xi xi xi xi Series – Mitsubishi VS Projector Connections Use the illustration below as a guide when connecting the System 4xi to a Mitsubishi VS projector. Refer to Mitsubishi VS documentation to continue the installation.
- Page 6 Connecting System 4xi xi xi xi xi to Mitsubishi LVP-X200 Projector If the System 4xi is already configured for a Mitsubishi LVP-X200 projector, go to step 4. If it is not set up correctly, it will be necessary to change switch settings on the System 4xi ’s Main Controller Board.
- Page 7 7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV cable onto the System 4xi output. Connect the 15-pin connector on the other end of the RGBS/HV cable to the PC-1 Input connector on the Mitsubishi LVP-X200 connector panel.