Philips BPC010 Series Mounting Instruction

Essential Smart Bright Solar Post Top
BPC010/050
<=3M
Battery
Type Number Flux(lm)
type
BPC010 LED20/MCT 2000lm Lithium iron phosphate 3.2V/10.8Ah
BPC010 LED30/MCT 3000lm Lithium iron phosphate 3.2V/14.4Ah
BPC010 LED40/MCT 4000lm Lithium iron phosphate 3.2V/14.4Ah
BPC010 LED50/MCT 5000lm Lithium iron phosphate 3.2V/21.6Ah
BPC050 LED20/MCT 2000lm Lithium iron phosphate 3.2V/10.8Ah
BPC050 LED30/MCT 3000lm Lithium iron phosphate 3.2V/14.4Ah
BPC050 LED40/MCT 4000lm Lithium iron phosphate 3.2V/14.4Ah
BPC050 LED50/MCT 5000lm Lithium iron phosphate 3.2V/21.6Ah
H
d D
1. Open the package and take out all accessories.
LAMP Screw fitting
3. Install the lamp on the light pole.
Pole (Φ58-Φ60)
Battery PV PV Remote Remote
CCT
parameter power voltage type distance
13W 4.5V Infrared ≤ 6m
3000K/
13W 4.5V Infrared ≤ 6m
4000K/
15W 4.5V Infrared ≤ 6m
6500K
20W 4.5V Infrared ≤ 6m
13W 4.5V Infrared ≤ 6m
3000K/
13W 4.5V Infrared ≤ 6m
4000K/
15W 4.5V Infrared ≤ 6m
6500K
20W 4.5V Infrared ≤ 6m
Type D H d
2000lm Ø420 123 Ø60
3000lm Ø420
123 Ø60
4000lm Ø420
123 Ø60
5000lm Ø520
137 Ø60
2. Place the M8 nut into the fixture slot and secure it
with the M8 screw.
M8 nut
M8 screw
4. Secure the light fixture to the light post using screws.
Torque: 5NM
On/Off: Wake up(On)/Sleep(Off)-Wake up the luminaire with last used working mode. Putting
the luminaire under sunlight will also wakeup the luminaire, to force Luminaire to sleep during
daytime, please use the manual switch on the luminaire.
Color temp. adjustment mode:
Auto: The luminaire contains 3 color temperature options. Every time you press the button, the
luminaire will change the color temperature once. The order is 3000K-4000K-6500K-3000K...
Cyclic conversion.
Sensor mode:
Ta
2H: Luminaire will detect sunset and automatically turn on at 30% intensity. If motion is
0-55°C
detected, the intensity will increase to 100% for 18 seconds. Turns off at battery low,
0-55°C
indicatively in 2 Hours on a full battery
0-55°C
4H: Luminaire will detect sunset and automatically turn on at 20% intensity. If a motion is
0-55°C
detected, the intensity will increase to 100% for 18 seconds. Turns off at battery low, indicatively
0-55°C
in 4 Hours on a full battery
0-55°C
6H: Luminaire will detect sunset and automatically turn on at 10% intensity. If a motion is
0-55°C
detected, the intensity will increase to 100% for 18 seconds. Turns off at battery low, indicatively
0-55°C
in 6 Hours on a full battery
Dimming mode:
Dim: (Dimming pattern with motion sensor disabled) Luminaire will detect sunset and
automatically turn on at 40% intensity for first 0.5 hour, 20% output for next 3 hours, 10% output
until battery low.
Full: Luminaire will detect sunset and automatically turn on at 100% intensity, until battery low
Partial: Luminaire will detect sunset and automatically turn on at 20% intensity, until battery low
Before installation, press the mechanical switch button on the luminaire to activate
the lamp, this will bring out the luminaire from sleep and activate remote functions.
To force Sleep mode (Say for storage purpose), press the physical button.
The factory default working mode of lamps is DIM. 3000K.
LED indication on lamp: Solid red light (full battery), flashing red light (low voltage),
slow flashing red light (charging), flashing green light (motion detected).
Try to install in a sunny place that is not shaded by trees, building, walls etc. so that the solar panel receive maximum
sunlight for charging the battery.
During installation, make sure the sensor module on the light fixture is facing the direction where people are walking.
Charge the product under sunlight for 8 hours before first use.
After installation, the working modes can be set from infrared remote controller.
This product does not need any external electrical connection. It works 100% on solar energy.
Detection of sunset is based on light intensity falling on solar panel.
The battery backup will reduce if the ambient temperature is < 0 degree celsius.
The light source and battery inside fixture are not replaceable, replace the product when it reaches end of life.
The product is designed for use on walkways, landscaping, etc. Not suitable for main roads, vehicle movement area.
The product mounting height should be <=3m.
This product contains lithium batteries, it is important to note that if the battery is not used for a long period of time
(>11 months), it may be in some state of over-discharge due to its self-discharge characteristics. Over-discharge may
degrade battery performance.
The product equipped with microwave motion sensor, detection range 4~5 meters, sensor delay time 18S.
Product is made of high quality polycarbonate material suitable for outdoor usage up to three years .Please exercise
caution while using the product when it comes to due life (3 years), since maintenance needs to be done on a monthly
basis to check visually the luminaire fixation, in order to avoid any potential hazard of breakage after due life.
switch button
sensor module