GE Holiday Classics GL-108B Use & Care Manual

108 LT LOLLIPOP
FOR INDOOR AND OUTDOOR USE
IMPORTANT SAFETY INSTRUCTIONS
When using electric products, basic precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
a)
Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products
b)
are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If
one is not provided, contact a qualified electrician for proper installation.
This seasonal use product is not intended for permanent installation or use.
c)
d) Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
e)
Do not let lamps rest on the supply cord or on any wire.
f)
g) Unplug the product when leaving the house, when retiring for the night, or if left unattended.
This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and electric shock it should
h)
not be played with or placed where small children can reach it.
i) Do not use this product for other than its intended use.
Do not hang ornaments or other objects from cord, wire, or light string.
j)
Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
k)
Do not cover the product with cloth, paper or any material not part of the product when in use.
l)
This product is equipped with push-in type lamps. Do not twist lamps.
m)
This product employs overload protection (fuse). A blown fuse indicates an overload or short -circuit
n)
situation. If the fuse blows, unplug the product from the outlet. Also unplug any additional strings or products
that may be attached to the product, Replace the fuse as per the user servicing instructions (follow product
marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be
present and the product should be discarded.
Read and follow all instructions that are on the product or provided with the product.
o)
SAVE THESE INSTRUCTIONS
p)
USE AND CARE INSTRUCTIONS
When the product is placed on a live tree, the tree should be well maintained and fresh. Do not place on
a)
live trees in which the needles are brown or break off easily. Keep the tree holder filled with water.
If the product is placed on a tree, the tree should be well secured and stable.
b)
Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire
c)
insulation or cords, cracks in the lampholders or enclosures, loose connections, or exposed copper wire.
When storing the product, carefully remove the product from wherever it is placed, including tree, branches, or
d)
bushes, to avoid any undue strain or stress on the product conductors, connections, and wires.
When not in use, store neatly in a cool, dry location protected from sunlight.
e)
USER SERVICING INSTRUCTIONS
Replace the fuse.
a) Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
b) Using a flathead screwdriver, open fuse cover.
Slide open the fuse access cover on top of attachment plug towards blades.
c) Remove fuses carefully.
d) Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided with product).
e) Close fuse cover. Slide closed the fuse access cover on top of attachment plug.
f) Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that
should not be removed. Discard product if the attachment plug is damaged.
Replace the lamp.
Step 1: Grasp plug and remove from the receptacle or
other outlet device. Do not unplug by pulling on cord.
Step 2: Pull lamp and plastic base straight out of lampholder.
Step 3: Replace lamp with only 3.5 Volt, 0.42 Watt,
super bright type lamp (provided with product).
If the new lamp base does not fit in lampholder, follow the steps
below step 3.
a) Remove the base of burned out lamp by straightening lamp leads
and gently pull lamp out.
b) Thread leads of new lamp through holes in old base with one
lead in each hole.
c) After lamp is fully inserted into base, bend each lead up,
like other lamps in the light set so that the leads will touch the contacts inside the lampholder.
-SEE OTHER SIDE-
MODEL NO.
GL-108B(0.36)
CAUTION:
1. To reduce the risk of overheating, replace burned-out lamps promptly. Use 3.5 Volt, 0.42 Watt lamps only.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Modifications not approved by the party responsible for compliance could void user's authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
For questions and/or assistance, call customer service at 1-877-398-7337
or visit us on the web at www.geholidaylighting.com
© 2017 Nicolas Holiday Inc., 9F., No. 37, Guangfu North Rd. Taipei, Taiwan 10560 All rights reserved.
INSTRUCTIONS FOR REPLACING
BULBS IN THE LIGHTED LOLLIPOP
CAUTION:
STEP 1:
Remove the screws.
STEP 2:
Open the lollipop and release metal tie from light string.
STEP 3:
Pull out the cap on bottom of tube.
STEP 4:
Pull out the light set through the tube.
STEP 5:
Remove the burned out bulb(s) and replace with
fresh replacement bulb(s).
(Use 3.5
Volt
CAUTION:
Step 1: Layout lollipop set in desired location.
Using screwdriver make starter hole.
Insert Stakes into hole. (Fig.1)
-CONTINUED FROM OTHER SIDE-
BE SURE ITEM IS UNPLUGGED BEFORE PROCEEDING.
/ 0.42 Watt midget bulb)
To reduce the risk of fire do not deliberately reposition either lampholder contact.
Fig.1
Step 2: Using wooden mallet. Pound stake into hole
up to outer ring as shown in Fig.2.
Fig.2
FP-17 PRINTED IN CHINA
Fig.3
Step 3: Insert lollipop Tubes onto Stakes. (Fig.3)