Advertisement
Quick Links
•
Lead cutter and former for axial components
•
Lead cutting operation for taped components can be continuously performed using the
same size settings once they are made
•
Possible to use together with 152B (motor drive)
Model No.
Forming size
Max.diameter of lead wire Φ0.8mm (MAX.) Φ0.5mm (MAX.)
Lead wire
Outer width of tape
Taping pitch
Dimensions
Weight
* Square lead wire is not adapted.
* Weight (w/ handle, clamp)
Cutting and forming for tape-type axial components and annealed copper lead
wire
Easy to use - simply set the taped components in place and turn the handle.
Ideal for processing tape-type components.
Improved, longer-life cutting blade for a clean, smooth cut.
Sealed bearings for longer service life and greater durability and efficiency.
Can be used for forming and cutting, forming only, or cutting only.
Lead forming tool
153-1
5.6mm pitch
5mm pitch
For annealed copper lead wire only
85mm (MAX.)
5mm
125(W)×130(H)×110(D)mm
2kg
154-1
Advertisement
Related Manuals for Hakko Electronics 153-1
Summary of Contents for Hakko Electronics 153-1
- Page 1 Lead cutting operation for taped components can be continuously performed using the same size settings once they are made • Possible to use together with 152B (motor drive) Model No. 153-1 154-1 5.6mm pitch 5mm pitch Forming size Max.diameter of lead wire Φ0.8mm (MAX.) Φ0.5mm (MAX.)
- Page 2 HAKKO 153 HAKKO 154 Cutting and forming Cutting and forming Forming Forming Cutting Cutting Part No. Name Specifications A1098 Bending wheel guide (P) for 153 A1099 Bending wheel guide (H) for 153 A1100 Bending wheel (H) for 153 A1101 Bending wheel (P) for 153 A1102 Bending wheel guide (H) for 154...
- Page 3 A1105 Bending wheel (P) for 154 A1106 Cutting blade for 153/154 A1094 Cutting wheel guide (H) for 153/154 A1095 Cutting wheel guide (P) for 153/154 A1096 Cutting wheel (H) for 153/154 A1097 Cutting wheel (P) for 153/154 B1387 Main shaft for 153/154/153 We recommend to replace the P side and H side at the same time when you need to change wheel guide or wheel.
- Page 4 is deformed due to use of leads thicker than those determined by the specifications. For the maximum applicable lead diameters, see the table below. HAKKO 153 HAKKO 154 Maximum applicable lead diameters ø0.8 ø0.5 Bending wheel guide with deformed blade New bending wheel guide spring Solution: Replace the bending wheel guide with a new one.
- Page 5 Case 3: Burrs are left at cut end faces. Why? The probable cause is a chipped cutting blade or the deterioration of the bending wheel and bending wheel guide (See the photo below). Replace them with new ones. Replacement parts list for HAKKO 153/154 If the backlash is too large when the cutting wheel guide is attached to the cutting wheel, they are worn out.
- Page 6 There are two major suspected causes. Cause 1: The handle was turned in a reverse direction during the work. Cause 2: The unit is being used for the cutting of leads that are not compliant with the specifications. Cause 1: The handle was turned in a reverse direction during the work.
- Page 7 are not compliant with the specifications. Cause: It is likely that the leads being cut are different from those normally used due to production changeover, or that cutting is being performed on leads that are not compliant with specifications. Solution: Check if the lead is compliant with the specifications of HAKKO 153/154 and if the bending wheel and bending wheel guide are not deformed.
- Page 8 Comparison with new parts using photo image Case 5: Adjustment of parts such as bending wheels and cutting wheels is becoming increasingly more difficult. Why? The probable cause is the deterioration of shaft and bending wheel. If the unit must be adjusted often due to the frequent changes of pitches to form (e.g. after each set of work), the grooves on the main shaft and bending wheel (where the screws touch) are scratched, and the unit will not operate smoothly.