Advertisement
Quick Links
uincy
ab
SPECIFICATIONS
Interior Dimensions
Exterior Dimensions
Weight (lbs)
Cubic Foot Capacity
Standard Electrical
Temperature Range
Common Unit Specifications
Operating Environment: Indoor use, altitude to 6,500 ft. (2,000m) Installation Category II,
Storage Temperature:
Approvals:
Compliance:
Common Unit Construction
Exterior: Powder-Coated Steel
Insulation: Fiberglass
Thermo-control: PID Microprocessor
Issue Rev 06.22
Copyright Quincy Lab Inc. 2022
Model 12-140E
MODEL
10-140E
12x10x10
INCHES W x H x D
31x25x25
(CM) W x H x D
13x15x11
INCHES W x H x D
33x38x28
(CM) W x H x D
19 lbs
115 / 120*
VOLTS / WATTS
Pollution Degree 2, ambient temperature 10
80% RH maximum.
o
-10
C/14
Underwriter's Laboratory Listed, Laboratory Equipment, C/UL
United States/Canadian. E212550 (115VAC models only)
UL Standard 61010-1, IEC 61010-1, 2nd Edition.
Quincy Lab Inc. 109 Shore Dr.
Digital Series Incubator
MODEL
12-140E
18x16x12
46x41x30
19x21x13
48x53x33
33 lbs
115 / 235*
o
o
o
F to 70
C/158
F, 70% RH maximum.
Interior: Aluminum
Door: 140E: Acrylic, 180E: Steel Insulated
Heater: Resistive-Tubular Incoloy
Burr Ridge, Illinois 60527
Operating Manual
For models 140E & 180E
Model 10-180E
MODEL
MODEL
10-180E
12-180E
12x10x10
18x16x12
31x25x25
46x41x30
13x15x11
19x21x11
33x38x28
48x53x33
19 lbs
33 lbs
115 / 270*
115 / 385*
o
o
o
C/50
F to 35
C/95
1800-482-4328
o
F,
PAGE 1
Advertisement
Related Manuals for Quincy lab Digital Series
Summary of Contents for Quincy lab Digital Series
- Page 1 Exterior: Powder-Coated Steel Interior: Aluminum Insulation: Fiberglass Door: 140E: Acrylic, 180E: Steel Insulated Thermo-control: PID Microprocessor Heater: Resistive-Tubular Incoloy Issue Rev 06.22 Quincy Lab Inc. 109 Shore Dr. Burr Ridge, Illinois 60527 1800-482-4328 Copyright Quincy Lab Inc. 2022 PAGE 1...
-
Page 2: General Operation
Safety Precautions Safety Precautions Read Operating Instructions Thoroughly Prior to Operation Read Opera�ng Instruc�ons thoroughly prior to opera�on and observe the following safety precau�ons: • Use only a grounded outlet that is rated for your model's electrical requirement. • Do not modify the unit or factory control se�ngs to operate the unit above the stated maximum opera�ng temperature. •... - Page 3 Menu Functions Guide To navigate the controller's menu, please refer to the easy-to-use Menu Guide below: Menu setting changes can be done quickly with our 4-button digital microprocessor. Your incubator's controller allows you to perform the following: Auto-tune your Incubator for maximum efficiency Set the operating set-point temperature Lock the set-temperature Select between degrees Fahrenheit or Centigrade...
- Page 4 AUTO-TUNING THE UNIT Your unit’s controller has been tuned from our factory to Once the desired set-point temperature has been set, achieve set-point temperatures at a faster rate. However, you will need to input the factory set passcode to access you can auto-tune your unit’s controller to work best with the tuning parameter.
- Page 5 Chamber Loading Understanding the unit's light pressure thermal convec�on and "load-effect" are necessary to op�mize unit performance. Ar�cle or media processing �mes and/or uniformity are largely dependent on load density and posi�oning. Important guidelines to chamber loading and processing: Load the incubator so that air circula�on within the chamber is not impaired. Leave a space between ar�cles on the shelf.
-
Page 6: Maintenance
For a complete list of replacement components, part and additional equipment, visit us on the web at www.quincylab.com Technical Support If you have any ques�ons or need technical assistance, contact Quincy Lab technical support for further assistance, or visit us on the web at www.quincylab.com Email: information@quincylab.com...