Bosch TDA3605GB Operating Instructions

Solving Minor Problems Yourself
Problem Possible Causes
Temperature control (I) on a Turn the temperature
very low setting control to the desired
position
Iron does not
Connection problems Check that the plug is
work or is not
inserted into the mains
heating up
socket correctly
The automatic shut-off Move the iron gently from
system (*) has been activated side to side to re-start it
There is no water in the tank Fill the water tank
The steam regulator (C) is in Set the steam regulator
the «0» position to the relevant position
Iron is not
Scale obstruction of internal Remove the steam
steaming
components regulator (C) and clean
it. If this does not help
contact an Authorised
Technical Service Centre
Temperature control (I) setting Set the temperature
is too low control within the steam
area (between the "••"
and "max") or turn the
steam regulator (C) to «0»
You have pressed the shot of Wait 5 seconds between
steam button (A) repeatedly each press of the jet of
without waiting for 5 seconds steam button
between each press
Water is
dripping from
Water has been left in the Always empty the tank
the holes in
tank (F) when the soleplate after ironing and set the
the soleplate
was cold, with the steam steam regulator to «0»
regulator (C) set at «1» or «2» after ironing and when
filling the tank
Tap or part distilled water has Mix distilled water with
not been used (see "Filling the tap water as directed
water tank" section) or other in the "Filling the water
products such as fragrant tank" section and never
water have been added to the add any other products
tank to the water tank
Deposits come Traces of lime scale are Carry out a cleaning
out through coming out of the steam cycle (see Multiple de-
the holes in the chamber scaling system section)
soleplate
No water in the tank. Add water to the water
tank.
Spray does not
work
Obstructed mechanism. Contact an Authorised
Technical Service Centre.
During first use: Certain This is completely normal
The iron
components on the appliance and will stop after a short
begins to
have been lightly greased at the while.
smoke when
factory and may produce a little
switched on.
smoke when initially heated.
Auto-shut off has been Move the iron gently
Flashing lamp activated. fromside to side to re-
on top of start it. The lamp (N) will
handle (*) then flash once before it
re-heats
(*) Model dependent
You can download this manual from the local homepages of Bosch
Thank you for buying the TDA36 steam iron from Bosch. This iron
has a lightweight design and is built to perform
These instructions contain valuable information about the unique
features of this iron and some hints to make ironing easier for
you.
Please visit www.bosch-home.co.uk for more product
information or to register your product, just follow the link
to the Online guarantee registration.
Before using the iron for the first time
Please carry out the following steps:
1. Remove the protective cover from the soleplate before using
the iron.
2. While the iron is unplugged, fill the water tank (F) with tap
water
3. Plug the appliance into the mains and set the temperature
control (I) to the "max" position by lining it up with the pointer
(H).
4. When the iron has reached the correct temperature (the pilot
lamp K goes out), set the steam regulator (C) to the «2» position
by lining it up with the pointer (D).
5. Hold the iron horizontally and repeatedly press the shot of steam
button (A). Any residue should come out of the soleplate (G).
It may smoke and smell – this is normal and will cease after a
short while.
6. If necessary, carefully clean the soleplate down with a dry, folded
cloth
Cleaning and Maintenance
Attention ! Risk of burns !
For general cleaning, follow the information below:
Problem Solution
Dirty/lightly Clean the body of iron or soleplate with a
marked iron body damp cloth then dry it.
or soleplate
Mark develops on Set the iron to its maximum temperature
soleplate during setting. Rub the iron a few times over
use with a dry cotton cloth folded several
times.
Heavily stained While the iron is cold, iron a linen cloth
soleplate soaked in white vinegar. Then dampen a
cloth with water and wipe the soleplate
clean and dry thoroughly.
Solution
DO NOT de-scale or clean the water tank with cleaning products
or solvents, as these could cause the iron to drip when using the
steam function.
DO NOT use a "professional steam cleaner" for cleaning the
appliance.
DO NOT use sharp objects or abrasive products to clean the
soleplate or any other part of the appliance. To keep the soleplate
in good condition, do not allow it to come into contact with metal
objects.
GUARANTEE TERMS
The terms of the guarantee for this appliance are in accordance with
that stated by our representative for the country in which it is sold.
Details of those conditions can be obtained from the retailer from
whom the appliance was purchased. The SALES RECEIPT must
be presented when making any claims against the terms of this
guarantee. We reserve the right to make technical modifications.
Environmental Care
This iron has been designed according to ecological criteria,
related to the sustainable development, analysing its whole
lifecycle - from material selection to its later reuse or recycling
- evaluating the improvement possibilities, from a technical,
economical and environmental point of view.
Before throwing a used appliance away, you should make it
noticeably inoperable e.g. cut off the mains lead and be certain to
dispose of it in accordance with current laws and regulations.
Your retailer, town council or local council can give you detailed
information about these.
This appliance is labelled in accordance with
European Directive 2002/96/EG concerning
used electrical and electronic appliances (waste
electrical and electronic equipment - WEEE).
The guideline determines the framework for the return
and recycling of used appliances as applicable throughout
the EU.
Important
This appliance has been designed exclusively for domestic use
and must not be used for industrial purposes.
Carefully read through the operating instructions for the appliance
and safeguard them for future reference.
Customer Service
Great Britain
Bosch Customer Service
Grand Union House
Old Wolverton Road
Milton Keynes
MK12 5PT
UK +44 (0)844 892 8923
IRL +353 (0)1450 2655
www.bosch-home.co.uk
002 TDA36..GB/03/10
TDA 36..
sensixx B2

Operating instructions

General safety warnings
• Danger of electric shocks or fire!
• This appliance is to be connected and used in accordance with
the information stated on its characteristics plate.
• This appliance must be connected to an earthed socket. If
it is absolutely necessary to use an extension cable, make
sure that it is suitable for 16A and has a socket with an earth
connection.
• The iron should not be used if it has been dropped, if there
are visible signs of damage or if it is leaking water. It must be
checked by an authorized Technical Service Centre before it
can be used again.
• Do not allow the power cable to come into contact with the
soleplate when it is hot.
• In order to avoid that, under unfavourable mains conditions,
phenomena like transient voltage drops or lighting fluctuations
can happen, it is recommended that the iron is connected to a
power supply system with a maximum impedance of 0.27Ω . If
necessary, the user can ask the public power supply company
for the system impedance at the interface point.
• This appliance is not intended to be used by persons (including
children) with reduced physical, sensory or mental capacities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning the use of the appliance
by a person responsible for their safety.
• Keep the appliance out of children's reach.
• Children should be supervised to ensure that they do not play
with the appliance.
• Remove the plug from the socket before filling the appliance with
water or before pouring out the remaining water after use.
• The appliance must be used and placed on a stable surface.
• When placed on its stand, make sure that the surface on which
the stand is placed is stable.
• The iron must not be left unattended while it is connected to
the supply mains.
• Unplug the appliance from the mains supply after each use, or
if a fault is suspected.
• The electrical plug must not be removed from the socket by
pulling the cable.
• Never immerse the iron in water or any other fluid.
• Do not leave the appliance exposed to weather conditions (rain,
sun, frost, etc.)
• With the aim of avoiding dangerous situations, any work or
repair that the appliance may need, e.g. replacing a faulty mains
cable, must only be carried out by qualified personnel from an
Authorised Technical Service Centre.