Advertisement
Quick Links
'
*( 6HFXULW\
JHVHFXULW\FRP
Product
Summary
‚qryÃI‚Ã%('$Ã6UQ!
‚qryÃI‚Ã%('#Ã6UQ!%
Installation
$73
These touchpads let you control all programming and operation of compatible security systems
(see the "Specifications" section).
The large 2-line, 16-character displays provide easy to read messages to indicate the current sta-
tus of the system. Both touchpads include police, fire, and auxiliary panic buttons that can be
activated anytime. A built-in sounder provides alarm, status, and button-press sounds. The ATP
2100 includes a swing-down door that reveals the buttons and a label with basic system operat-
ing commands. The ATP2600 has a flip-top that hides the display and covers the buttons when
down. Both touchpads also include menu scroll buttons to the right of the display and a hardwire
contact input.
Tools and Equipment Needed
•
4-conductor, 22- or 18-gauge wire
•
Screwdriver
•
#6 screws and anchors (included)
•
Panhead screws for gang box installation
•
Saw or utility knife for cutting wallboard
Guidelines
•
Mount the touchpads in an environmentally controlled area (32°F to 120°F/0°C to 49°C).
•
When mounting the ATP2100, allow at least 3 inches below it for the swing-down door.
•
When mounting the ATP2600, allow at least 2 inches above it for the flip-top display.
•
Do not exceed the maximum available power (see panel Installation Instructions).
•
Table 1 describes the power used by the touchpads.
•
Table 2 describes the maximum wire lengths allowed between the touchpad and the panel.
Table 1: Touchpad Power Usage
Current (mA)
165
Maximum alarm current with the
buzzer sounding and the touchpad
illuminated from a button press
110
Typical operation
30
Power saving mode (no panel AC
power)
Table 2: Maximum Touchpad Wire Lengths
Wire Gauge
Max. Power & Bus Wire
(Unshielded or
Length to Panel
Shielded)
18
750 feet
22
300 feet
$73 7RXFKSDGV
,QVWDOODWLRQ ,QVWUXFWLRQV
Conditions
Wire Gauge
(Shielded)
18
22
'RFXPHQW 1XPEHU 5HY &
6HSWHPEHU
Max. Hardwire Input
Wire Length
1000 feet
350 feet
1
Advertisement
Related Manuals for GE ATP2100
Summary of Contents for GE ATP2100
- Page 1 Mount the touchpads in an environmentally controlled area (32°F to 120°F/0°C to 49°C). • When mounting the ATP2100, allow at least 3 inches below it for the swing-down door. • When mounting the ATP2600, allow at least 2 inches above it for the flip-top display.
-
Page 2: Mounting The Touchpad
Figure 2. Mounting Hole Locations 3. Loosen the lower side screws slightly to remove the lower cover, then mark the lower mounting hole (Figure 3). Note On the model ATP2100, you must remove the door to access the lower side screws. Mounting Hole Screws Figure 3. -
Page 3: Wiring The Touchpad To The Panel
Express, Concord, or Concord Ultra panel with software version 2.0 or later: 1. With the panel powered up, connect the cable to the Programming Touchpad Header (Figure Figure 7. Connecting a Programming Touchpad—Concord Express Shown, Concord Similar ATP2100 & ATP2600 Touchpads Installation Instructions... -
Page 4: Adjusting Display Brightness And Contrast
ƒ and displays the new setting and brightness level. 5. Exit user programming mode. To adjust display contrast: Enter configuration mode by pressing the D and 6 buttons together for at least two seconds. The display shows DA n. ATP2100 & ATP2600 Touchpads Installation Instructions... -
Page 5: Troubleshooting
3. Enter the desired unit number (0 - 3 for Concord Express, 000 - 015 for all others), then press ƒ . The display shows the new touchpad unit number. Note Do not use unit number 15 in Concord RF systems. 4. Press ‚ to exit from the configuration mode. ATP2100 & ATP2600 Touchpads Installation Instructions... -
Page 6: Specifications
Notices FCC Part 15 Information to the User Changes or modifications not expressly approved by GE Security can void the user’s authority to operate the equipment. FCC Part 15 Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.