Download Print this page

Advertisement

Quick Links

Battery Backup
Garage Door Openers
BATTERY BACKUP KIT 2.3Ah V-06 - ORDER NO. 61932
ITEM
DESCRIPTION
1
BATTERIES COVER
2
BATTERIES SUPPORT
3
BATTERY 12V SEC 12-2.2 AGM TYPE
4
BATTERY COUPLING WIRE - ESV24
5
BATTERY HARNESS
6
PAN HEAD SCREW W/WASHER M4x8
7
CABLE CLAMP ACC-1.5 (3/16")
8
CHARGER BOARD SBC-02
9
SBC-02 CHARGER HARNESS
10
SBY-2 BATTERY HARNESS
PACK #1 (SECTIONAL DOOR OPENERS)
11
HEX STANDOFF M4
12
PAN HEAD SCREW W/WASHER M4x8
13
THRUSS SER HD SCREW "S" RoHS M4x8
14
TAPTITE SCREW "P" M4 X 8
15
PCB SUPPORT 76X27
PACK #2 (ROLLER DOOR OPENERS)
16
TAPTITE SCREW "P" M4x8
17
TAPTITE SCREW "P" M4x10
18
CABLE CLAMP ACC-1.5 (3/16")
Important Safety Instructions
WARNING!
ELECTROCUTION!
CAUTION:
Muscular strain
Fall from ladder
Burns
Doc # 160018_01
Part # 13403
Released 05/05/14
2.3 Ah V-06 Installation Instructions
QTY
ORDER
CODE
1
16460
1
16480
2
15470
1
12005
1
15670
2
10320
1
11750
1
60915
1
14117
1
15660
2
11190
4
10320
2
10503
3
10580
1
16421
4
10580
2
10570
1
11750
DO NOT short the output of batteries. Serious personal injury and/or property damage
can result from failure to follow this warning
During charging and discharging cycles the lead-acid batteries may release explosive
gases. Ensure that the area around the batteries is well ventilated
Take care not to allow any metal objects to make contact with the positive and negative
terminals. This will short circuit the battery causing sparks and possible damage to the
battery, or even cause an explosion.
The battery box unit should be installed away from sprinkler systems.
DO NOT immerse in water or spray directly with a hose or other device.
Disconnect the power cord from mains power before making any repairs or removing
covers.
Practice correct lifting techniques
Ensure ladder is the correct type for job.
Ensure ladder is on flat ground.
Ensure user has 3 points of contact while on ladder.
DO NOT handle damaged or leaking batteries
Wear appropriate protective clothing and avoid touching your eyes after working with
batteries.
The battery backup kit contains sealed lead-acid batteries that must be disposed of
properly at the end of their useful life.
Gen 2
Swing Gate Openers
BATTERY BACKUP KIT SBC-02 - ORDER NO. 90488
ITEM
DESCRIPTION
19
BATTERY CHARGER BOX ASSEMBLY
20
CHARGER ASSY SBC-02
ACCESSORY PACK
21
TIE MOUNT CM-13 (ADHIESIVE)
22
CABLE TIE 4" GT-100M
23
BRACKETS GE 44 621
24
SCREW "P" M3.5 X 13 FOR GW 44 621
Sliding Gate Openers
BATTERY BACKUP KIT ESV24V2 - ORDER NO. 61928
ITEM
DESCRIPTION
25
BATTERY CP1223H 12V 2.3H
26
CHARGER ASSY SBC-02
27
BATTERY COUPLING WIRE - ESV24
28
BATTERY HARNESS
29
TAPTITE SCREW "P" M3 X 8
Kit
QTY
ORDER
CODE
1
90150
1
60914
4
11835
4
14160
4
62480
4
62826
QTY
ORDER
CODE
2
15470
1
60914
1
12005
1
15670
4
10560

Advertisement

loading

Summary of Contents for B&D V-06

  • Page 1 Battery Backup Gen 2 2.3 Ah V-06 Installation Instructions Garage Door Openers Swing Gate Openers BATTERY BACKUP KIT 2.3Ah V-06 - ORDER NO. 61932 BATTERY BACKUP KIT SBC-02 - ORDER NO. 90488 ITEM DESCRIPTION ORDER ITEM DESCRIPTION ORDER CODE CODE...
  • Page 2 Roll Up Door Opener Set Up GDO-6V4 EasyRoller , RDO-1V3 ® SBC-02 Mount the Charger Board a. Unplug the drive unit from mains power. b. Remove the timing cover and light diffuser. c. Mount the Charger Board on the chasis and secure with four (4) Taptite ‘P’ M4x8 screws d.
  • Page 3 Overhead Door Opener Set Up GDO-9V2 GEN2 Enduro, GDO-9V3 GEN2 Dynamo, SDO-2V2 CAD P Diamond & SDO-3V2 CAD S Light Diffuser Grommet Mount the Charger Board a. Unplug the drive unit from mains power. b. Remove screws and swing open the cover. c.
  • Page 4 Swing Gate Opener Set Up DCB-05V2 WARNING! Do not connect the batteries until you have connected wiring on the charger board. Mount the Charger Board a. Unplug the Control Box from mains power. b. Remove the Control Box’s cover. c. Secure the adhesive mounts to the Charger Board with cable ties .
  • Page 5 Sliding Gate Opener Set Up NeoSlider Mount the Charger Board a. Unplug the drive unit from mains power. b. Remove the main cover and unscrew the lid from the cover. c. Mount the Charger Board inside the cover using four (4) M3x8 screws d.
  • Page 6: Troubleshooting

    Troubleshooting Symptom Possible cause Remedy Door stops or moves very slowly Batteries may be weak or have Connect mains power and allow the batteries under battery power no charge to charge. This may take 24 - 48 hours to reach maximum charge capacity.
  • Page 7: Warranty And Exclusion Of Liability

    Warranty and Exclusion of Liability 1. This Warranty is given by Automatic Technology (Australia) Pty Ltd door manually to the open or closed position; (ABN 11 007 125 368) (ATA), 6-8 Fiveways Boulevard, Keysborough (i) door surface area and/or weight exceeding 28m2 and 270kg respectively; 3173, 1300 133 944, sales@ata-aust.com.au (j) the door used with the Product not being in safe working order and 2.
  • Page 8 B&D Doors is a division of B&D Australia Pty Ltd ABN 25 010 473 971 B&D Doors, 34-36 Marigold St, Revesby, NSW, 2212 6 - 8 Fiveways Boulevard, Keysborough, VIC, Australia 3173 P: 13 62 63 E: enquires@bnd.com.au P: 1300 133 944 E: sales@automatictechnology.com.au W: www.bnd.com.au W: www.automatictechnology.com.au...

This manual is also suitable for:

Sbc-2Esv24v2619329048861928