GE LED 400 7MM LIGHTS Quick Manual

MODEL NO. 24LED-7MMb-400(0.105)
LED 400 7MM LIGHTS
FOR INDOOR USE ONLY
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
READ AND FOLLOW ALL
a)
SAFETY INSTRUCTIONS.
b) Do not use seasonal products outdoors unless marked suitable
for indoor and outdoor use. When products are used in outdoor
applications, connect the product to a Ground Fault Circuit
Interrupting (GFCI) outlet. If one is not provided, contact a
qualified electrician for proper installation.
c) This seasonal use product is not intended for permanent
installation or use.
d) Do not mount or place near gas or electric heaters, fireplaces,
candles or other similar sources of heat.
e) Do not secure the wiring of the product with staples or nails, or
place on sharp hooks or nails.
f) Do not let lamps rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, when retiring for the
night, or if left unattended.
h) This is an electric product-not a toy! To avoid risk of fire, burns,
personal injury and electric shock it should not be played with or
placed where small children can reach it.
i) Do not use this product for other than its intended use.
j) Do not hang ornaments or other objects from cord, wire, or light
string.
k) Do not close doors or windows on the product or extension cords
as this may damage the wire insulation.
l) Do not cover the product with cloth, paper or any material not
part of the product when in use.
m)This product is equipped with push-in type lamps. Do not twist
lamps.
n) Read and follow all instructions that are on the product or
provided with the product.
SAVE THESE INSTRUCTIONS
o)
USE AND CARE INSTRUCTIONS
a) When the product is placed on a live tree, the tree should be well
maintained and fresh. Do not place on live trees in which the
needles are brown or break off easily. Keep the tree holder filled
with water.
b) If the product is placed on a tree, the tree should be well secured
and stable.
c) Before using or reusing, inspect product carefully. Discard any
products that have cut, damaged, or frayed wire insulation or
cords, cracks in the lampholders or enclosures, loose
connections, or exposed copper wire.
d) When storing the product, carefully remove the product from
wherever it is placed, including tree, branches, or bushes, to
avoid any undue strain or stress on the product conductors,
connections, and wires.
e) When not in use, store neatly in a cool, dry location protected
from sunlight.
USER SERVICING INSTRUCTIONS
Replace the lamp.
1. Grasp plug and remove from the receptacle or
other outlet device. Do not unplug by pulling cord.
2. Pull lamp and plastic base straight out of
lampholder.
3. Replace lamp with only 3.3 Volt, 0.066 Watt,
LED type lamp (provided with product).
If the new lamp base does not fit in lampholder, follow the steps
below step 3.
a) Remove the base of burned out lamp by straightening lamp leads
and gently pull lamp out.
b) Thread leads of new lamp through holes in old base with one
lead in each hole.
c) After lamp is fully inserted into base, bend each lead up, like
other lamps in the light set so that the leads will touch the
contacts inside the lampholder.
LED-10-1
CAUTION:
1. Replace lamps only with 3.3 volt, 0.066 watt
spare lamps provided with this product.
2. Risk of fire. This product does not contain lamp shunts, which
allow the product to operate if one lamp burns out. Do not
replace lamps with other than the spare lamps provided with
this product.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Warning:
expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
For questions and /or assistance, call customer service at
1-877-398-7337 or visit us on the web at www.geholidaylighting.com
©2021 Nicolas Holiday Ltd. 204 Spring Hill Road Trumbull, CT 06611
9F., No. 37, Guangfu North Rd. Taipei, Taiwan 10560
All rights reserved.
TROUBLESHOOTING
PROBLEM
If the
product
does not
light
If a based
LED is
missing
If an LED
fails to
light
(shorts or
opens)
LEDs fail
to switch
from white
to multi
Changes or modifications to this unit not
FP-21 PRINTED IN CHINA
POSSIBLE CAUSE
One or more of the Unplug the set at the outlet.
based LEDs may have Starting with the first unlit
loosened from the LED, gently push (don't twist)
socket during each LED base firmly into the
transporting. There is a socket. If still does not light,
break in the circuit then remove each based
between the LED leads LED and check for out of
and the socket place lead wires. Make
terminals. Male/female certain connectors fully
connectors not fully inserted and securing cap
inserted together. Non fully tightened. Step on foot
working control box. pedal to turn LEDs on.
Foot pedal in off
position.
One or more of the Mark socket(s) with a piece
based bulbs may have of tape and unplug the set.
come out of the socket Replace the based LED or
when transporting. use one of the spare based
LEDs included with product.
Incorrect LED, The LED may be out or dimly
premature LED failure lit. Replace bad LEDs as
or voltage is too high. soon as you find them.
If applicable, then a Contact Customer Support.
defective control box or
color change foot
pedal.
CORRECTIVE ACTION