Black & Decker BDL150S Instruction Manual

B B D D L L 1 1 5 5 0 0 S S 3 3
B B D D L L 1 1 5 5 0 0 S S
1 1 1 1
B B D D L L 1 1 5 5 1 1 S S 1 1 - -
B B D D L L 1 1 5 5 1 1 S S 1 1 - -
INSTRUCTION
MANUAL
Catalog Nos. BDL150S & BDL151S
BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
1-800-544-6986
IF YOU SHOULD HAVE A QUESTION OR EXPERIENCE A
PROBLEM WITH YOUR BLACK & DECKER PRODUCT,
CALL 1-800-544-6986
BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No., TYPE No., AND
DATE CODE (e.g. 20000130M). IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CAN
RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT, GIVE
US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.
ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
Cat Nos. BDL150S, BDL151S Form # 585439-00 (JUN-03-2) Copyright © 2003 Black & Decker
Printed in China
WARNING: To reduce the risk of injury, user must read and understand instruction
manual.
SAVE THESE INSTRUCTIONS
Safety Instructions
• Do not operate the stud sensor in explosive atmospheres, such as in the presence of
flammable liquids, gases, or dust.
• Use the stud sensor only with 9 volt alkaline battery. Use of any other batteries may create a
risk of fire.
CAUTION: Material thickness, type of material, moisture content, and other variables can
effect sensing results. The sensor may detect electric wiring or pipes in the same manner
that studs are detected depending on their location to the wall surface. Use caution when
drilling, nailing or cutting into walls, floors and ceilings which may contain electrical wiring or
pipes. These items may be detected by the Stud Sensor in the same manner in which studs
are detected. Because studs are normally spaced 16 inches (406 mm) or 24 inches (610
mm) apart and are usually 1-1/2 inches (38 mm) wide, beware of anything closer together
or of a different width. Always turn off the power when working near electrical wires.
INSTALLING THE BATTERY
Remove the battery compartment cover (D) by pressing in the tab in the center of the cover
and pulling back. Insert a fresh 9 volt alkaline battery into compartment and connect to
battery cable. Replace the battery compartment cover and snap shut.
Operating Instructions
CALIBRATION AND SCANNING
CALIBRATION
1.) Hold unit straight up and down and place flat against wall as shown in Figure 2.
2.) Press in and hold the sensor ON/OFF button (C) while calibrating and continue holding in
button while scanning.
a.) The upper GREEN LED (A) will light,
b.) The unit will beep once while it is calibrating,
c.) The bottom RED LED will light.
SCANNING
For stud sensing up to 3/4 in. (19 mm) deep (Model BDL150S). Up to 1-
(Model BDL151S).
1.) After calibration, while still holding in button, slide sensor slowly, (Figure 2) horizontally
across surface of wall without lifting or tilting.
2.) The upper GREEN LED will light and a beeper will sound when an edge is detected,
mark that spot as shown in Figure 3.
Repeat this cycle coming from the other direction to confirm the mark.
TIPS FOR OPTIMUM USE
• Test batteries before each use. Press and hold the on/off switch until the RED LED remains
on. Then move your free hand toward the back of the unit. The GREEN LED should
illuminate and then go out as you move your hand away from the unit. Replace the batteries
if the GREEN LED does not illuminate.
• Hold stud sensor straight up and down.
• Because studs are normally spaced 16 inches or 24 inches apart and are 1-1/2 inches
wide, beware of anything closer together or of a different width. Doors and windows are
constructed with studs and headers which are closer together.
• Avoid materials which have inconsistent density such as:
• Carpeting and padding
• Ceramic floor tile
• Wallpaper containing metallic foils or fibers. Generally, surfaces covered with regular
wallpaper or fabric will scan with no difference in function.
• Walls that are freshly painted and are still damp.
• Excessively thick plaster and lath.
Maintenance
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.
/ / 4 4 " " S S t t u u d d S S e e n n s s o o r r
3 3 / / 4 4 " " S S t t u u d d S S e e n n s s o o r r
/ / " " D D e e e e p p S S t t u u d d S S e e n n
/ / " " D D e e e e p p S S t t u u d d S S e e n n
2 2 2 2
3/4" Stud Sensor
1
/
2
1
& &
& &
s s o o r r
s s o o r r
C
2
3
User can mark
the location for
nailing, securing,
etc...
3
2
*Recess edge
indicates
approximate
center of stud...
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (other than those listed in this manual) should be performed by authorized service
centers or other qualified service personnel, always using identical replacement parts.
WARNING:
hazardous.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Service Information
All Black & Decker Service Centers are staffed with trained personnel to provide customers
with efficient and reliable power tool service. Whether you need technical advice, repair, or
genuine factory replacement parts, contact the Black & Decker location nearest you. To find
your local service location, refer to the yellow page directory under "Tools—Electric" or call:
1-800-544-6986 or visit www.blackanddecker.com
Full Two-Year Home Use Warranty
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material
or workmanship. The defective product will be replaced or repaired at no charge in either of
two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom
it was purchased (provided that the store is a participating retailer). Returns should be made
within the time period of the retailer's policy for exchanges (usually 30 to 90 days after the
sale). Proof of purchase may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may be
required. Black & Decker owned and authorized Service Centers are listed under "Tools-
Electric" in the yellow pages of the phone directory and on our website
www.blackanddecker.com.
This warranty does not apply to accessories. This warranty gives you specific legal rights and
in. (38mm) deep
you may have other rights which vary from state to state. Should you have any questions,
contact the manager of your nearest Black & Decker Service Center. This product is not
intended for commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-544-6986 for a free replacement.
Problem
• LEDs do not light.
• LEDs light in too many
places.
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
A.) Green LED (
A
Emitting Diode)
B
B.) Red LEDs (4)
C.) On/Off Button
D.) Battery Compartment
Cover
3/4" Stud Sensor
1
LED brightens to
signal edge of stud...
*Based on stud 1-1/2 inches wide
The use of any accessory not recommended for use with this tool could be
T T R R O O U U B B L L E E S S H H O O O O
T T R R O O U U B B L L E E S S H H O O
Possible Cause
• Weak battery.
• Nothing to detect in that
area.
•May have been calibrated
over a stud.
• Detects other objects
besides studs.
• Electrical wiring and
metal or plastic pipes
may be near or touching
back surface of wall.
FEATURES
Light
D
3
User can mark
the location for
nailing, securing,
etc...
2
*Recess edge
indicates
approximate
center of stud...
T T I I N N G G
O O T T I I N N G G
Solution
• Replace with fresh batteries.
• Start again moving farther to either
side.
• Because studs are normally
spaced 16 inches or 24 inches apart
and are 1-1/2 inches wide, beware
of anything closer together or of a
different width.
See 'Tools-Electric'
– Yellow Pages –
for Service & Sales