Panasonic Aicure UD40 Series Installation Manual

Thank you very much for purchasing the UD40 Series Line Type LED Head.
Be sure to read this installation manual first and install this product properly.
Keep this manual in a safe place after reading this and look it up as needed.
Safety Precautions
Please use the following precautions to prevent injuries and accidents.
Do not use this product in an environment containing flammable gas.
Doing so may cause an explosion.
Do not throw this product into fire.
Doing so may cause the electrical components to explode.
Never look into the direct light or its reflection or expose your skin to such
Prohibited
light while the LED is turned ON.
Doing so may harm or irritate your eyes and skin.
Install this product at a place where the human body will not be exposed
to the LED-UV light.
Being exposed to LED-UV light may harm or irritate your skin.
When a human body is in danger of being exposed to the LED-UV light or reflected
UV light, cover the light with an enclosure with appropriate permeability and heat
characteristics to block the UV light.
Be sure to wear protective glasses and protective gears when installing or
operating this product.
Be sure to
Doing so without them may harm or irritate your eyes and skin.
observe
The light emitted from this product includes UV light of 365nm or 385nm
wavelength. Make sure to wear protective glasses to block the UV light.
Make sure to shut off the power supply when cleaning the LED head.
Doing so without shutting off the power supply may harm or irritate your eyes and
skin, or may result in electric shocks.
Do not disassemble or alter the product.
Doing so may result in accidents or injuries.
Doing so may result in abnormal heating or fuming.
No
disassembling
Doing so may harm or irritate your skin by being exposed to LED-UV light.
Prevent any foreign materials, including liquid, flammable materials and
metals, from entering into this product.
Doing so may result in abnormal heating or fuming.
Do not perform any installation work (such as connecting or disconnecting)
with the power turned ON.
Doing so may result in electric shocks.
Prohibited Avoid placing any object on this product or block the ventilation hole.
Doing so may result in burnout by heating.
Do not touch with bare hands immediately after irradiation and during
irradiation.
This product becomes very hot and may cause burn injuries.
Use this product in a condition sufficiently under the threshold guaranteed
or specified.
Exceeding the threshold of the characteristics/performance guaranteed may
damage the product.
Do not touch the terminal while the power is being supplied.
Doing so may result in electric shocks.
Securely connect the power line and the connector.
Improper connection may result in abnormal heating or fuming.
Do not use input power outside of the specified range.
Be sure to
Doing so may result in burning out.
observe
Connect the ground wire securely.
Doing so may result in electric shocks or malfunctions.
Do not use this product in a place where the temperature changes
drastically or a dew condensation occurs.
Doing so may result in a malfunction.
Do not use this product at a place where extreme vibration or shock is
applied.
Doing so may result in a malfunction.
Included Items
1
Connector for wiring：1 set
Connector Part No.：NJW-2824-PF16, NJW-2824-PFX16
(NANABOSHI ELECTRIC MFG CO., LTD.)
Precautions on Installation
2
Standard on the safety of LED products
LED light source that is used in this product, has
become the scope of application of the
"Photobiological safety of lamps and lamp systems"
Standard ：JIS C7550:2011, IEC62471:2006
Class ：Risk Group 3
However, we recommend a safety management
in consideration for the safety of the user,
corresponding to the Class 4 "Standard on the
safety of laser products"
<Reference：Standard on the safety of laser products>
：JIS C6802:2011, IEC60825-1 Edition2.0:2007
Standard
：Class 4 LED product
Class
Wavelength：365±10nm, 385±10nm
Handling of LED Products at Overseas
Currently, in JIS and IEC, LED is ordered to exemption of "Standard on the safety of
laser products". However, since you may be adopting the old edition depending on
the country or region, please check the laser safety regulations and standards of the
country to be used.
General Precautions
Cables connected to this product, please use the products by our company
designation or recommended. Any malfunctions and damages occurred from use of
the other products are not covered by the product warranty.
Do not disassemble, remodel the camera or change its internal settings.
Any failure or damage arising out of using the disassembled or altered product will
not be covered by the warranty.
Aicure LED Line Type UV Curing Systems
UD40 Series LED Head
Installation Manual
Warning
Caution
Consider the followings
when installing and using this product.
UV
Installation Environment
Ambient Temperature 0 to +35℃
Ambient Humidity 30 to 85%RH (Without dew condensation and freezing)
A place free from dust, oil smoke, conductive dust, corrosive or flammable gas,
salt content or iron dust.
A place free from splashes of water, oil or chemicals.
A place free from sudden temperature changes, oscillation or shocks.
A place without direct sunlight.
A place without high magnetic field or intense electric field.
Power Supplies
Prepare the two types of power supplies of the following specifications for the number of
blocks to be connected.
For LED：Constant current DC power supply : Open Voltage : 40V, Max current : 3A
For Fan ：Constant voltage DC power supply : DC12V±5%, Max current : 1A
Prepare the power supply of the following specifications when control the fan all at once.
Constant voltage DC power supply
Please contact us for details.
Wiring
At connecting the power supply, please do not connect the power supply of a different
kind or in reverse polarity.
Doing so may result in damage.
Cable to be soldered to the connector, please use the cable cross-sectional area of
2
larger than 0.5mm (AWG23). Make sure to solder it properly.
See the official website or the catalog of "NANABOSHI ELECTRIC MFG CO., LTD." for details on
soldering onto the connector and its handling.
Keep the cable length within 5m.
Please contact us if you want to use the cable longer than 5m.
Hold the connector (plug) area when connecting / disconnecting the cable.
Wire the connection cable without extra load being applied.
Installation
Do not cover up the ventilation hole.
Doing so may result in abnormal heating.
Do not touch the UV emitting window (glass) with bare hands.
Doing so may result in smudge.
The UV emitting window is protected by the glass.
Doing so may result in damaging the glass if a shock is applied to this area.
If this area becomes dirty, the UV light output intensity may be degraded.
Use alcohol (Ethanol, IPA) to wipe off smudges completely, if dirty.
Make sure to take safety measures (such as an interlock or smoke detector installation)
externally so that the entire system operates safety in case of a system failure or an
error caused by external factors.
Before Turning On the Power
Verify that the all wirings and connections are correct before turning on the power.
Intake / Exhaust Direction of Fan
At the standard specification, the fan intakes the air from the side panel and exhausts
toward the back panel.
Please contact us if you want to change the intake/exhaust direction of fan.
Dimensions
3
Dimensions and Installation Space
Unit：mm
B
A
As an example, external dimensions of three blocks type are shown.
Dimensions of from A to C,refer to the table.
In the product of 4-6 blocks type, connectors to be connected to the main body will
be two.
Please have a margin to installation space.
Exhaust air from the fan, please do not return to the air intake area.
: DC12V±5%, Max current : (1×number of blocks) A
50 50
50
or more or more
Number of
A B
Blocks
1 159 72
2 231 144
3 303 216
C
4 405 288
5 477 360
6 549 432
C
77
77
77
107
107
107