Sealey Quality MACHINERY YAJ15-30 Instructions

MODEL No's yaJ15-30
Thank you for purchasing a Sealey jack. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
Important: REaD ThESE InSTRuCTIOnS CaREfuLLy. nOTE ThE SafE OPERaTIOnaL REQuIREMEnTS, WaRnInGS anD CauTIOnS.
uSE ThIS JaCK CORRECTLy anD WITh CaRE fOR ThE PuRPOSE fOR WhICh IT IS InTEnDED. faILuRE TO DO SO May CauSE
DaMaGE anD/OR PERSOnaL InJuRy, anD WILL InvaLIDaTE ThE WaRRanTy. RETaIn ThESE InSTRuCTIOnS fOR fuTuRE uSE.
1. SafETy InSTRuCTIOnS
 Disconnect jack from air supply before changing parts, servicing
or performing any maintenance.
 WaRnInG! Ensure correct air pressure is maintained and not
exceeded. Recommended pressure 116-145psi or 174psi for
YAJ20-40LR. Required air flow 10.5cfm or 11.5cfm for
YAJ20-40LR.
 Keep air hose away from heat, oil and sharp edges. Check air
hose for wear before each use, and ensure that all connections
are secure.
 Ensure Jack is kept clean and in good working order. Immediately
repair or replace damaged parts.
 Use recommended parts only. Incorrect parts may be dangerous
and will invalidate the warranty.
 Use a qualified person to lubricate and maintain the jack.
DO nOT use brake fluid to top up system. Use Sealey hydraulic
oil only.
 Locate jack in a suitable, well lit work area. Keep area clean and
tidy and free from unrelated materials.
 Use jack on level & solid ground, preferably concrete. Avoid
tarmacadam since jack may sink in.
 Place wedges under wheels of vehicle (but ensure wheels of jack
can freely move).
 Ensure the vehicle handbrake is engaged (or in "PARKED"
mode), and switch the engine off.
 Ensure minimum distance of 0.5m between vehicle tilt & static
objects such as doors, walls, etc.
 Ensure all non essential persons keep a safe distance and that
there are no passengers in the vehicle to be jacked up.
 Place jack under vehicle manufacturer's recommended jacking
points (see vehicle handbook).
 Check that the jacking point is stable and centred on the jack
saddle and is free from grease or oil.
 Ensure jack wheels are free to move and that there are no
obstructions.
 DanGEr: Use jack for lifting only, NOT for supporting the raised
load. Use correctly rated axle stands under vehicle before
proceeding with task.
 DO nOT apply your body weight to the handle during jacking.
The handle is only for moving the jack to and from the lifting
location.
 DO nOT operate the jack if parts are missing or damaged.
 DO nOT exceed the rated capacity of the jack.
 DO nOT allow the vehicle to move during lifting and do not use
the jack to move the vehicle.
 DO nOT jack a vehicle which may result in the spillage of fuel,
battery acid, or dangerous substances.
 DO nOT work under the vehicle until Axle Stands have been
correctly positioned.
 DO nOT use the jack for purposes other that than which it is
designed for.
 DO nOT adjust the safety overload valve.
 DO nOT yank the hose from the air supply, and DO nOT direct
air from the air hose at yourself or others.
 Ensure there are no persons or obstructions beneath the vehicle
before lowering.
 When not in use disconnect jack from the air supply, and store in
the lowered position in a safe, dry, childproof area.
 WarnInG! Turn off air supply and de-pressurise the control
nozzle before removing the pump unit from any installation or
mobile system.
Failure to comply with this instruction may damage the unit and
will invalidate your warranty.
INSTRUCTIONS FOR :
aIR OPERaTED JaCKS
TELESCOPIC
yaJ15-30DC yaJ20-40
2. SPECIfICaTIOnS
Note: The maximum heights shown may be extended by use of the
extension pins
Model no yaJ15-30 yaJ15-30DC yaJ20-40 yaJ20-40DC yaJ20-40LR
Maximum
Capacity
Minimum
height
Maximum height/Capacity (mm/Tonne)
Stage 1
Stage 2
Extension 45/75mm
Chassis
Length
Length inc. handle
Position 1
Position 2
Position 3
Width
Working
Pressure
air flow
Weight
3. InTRODuCTIOn
3.1.
4. aSSEMBLy
4.1.
4.1.1. Remove a circlip from either side of the large pin (fig.1A).
4.1.2. Slide out the pin and place the handle into the opening. Slide
4.2.
4.2.1. Screw in the two air hoses from the handle into the jack.
4.2.2. The hose marked orange must be screwed into the left-hand
4.2.3. Ensure the hoses are tight and do not obstruct the movement
Original Language Version
yaJ20-40DC
30Tonne 30Tonne 40Tonne
175mm 150mm 175mm
472/15 409/15 472/20
393/30 343/30 393/40
45/75mm 45/75mm
480mm 430mm 480mm
460mm 1280mm 460mm
1380mm 1600mm 1380mm
1700mm - 1700mm
290mm 290mm 290mm
116- 116-
145psi 145psi 145psi
10.5cfm 10.5cfm 10.5cfm
39kg 31kg
Ideal for workshop or roadside use, these jacks take the effort
out of lifting heavy plant, tractors and commercial vehicles.
Models feature dead man's control for extra safety
(detachable on Model No's YAJ15-30DC and YAJ20-40DC
making these models extremely portable) and multi-position
locking handles. Each jack is supplied with a 45mm and
75mm extension to help close the gap between the saddle of
the jack and the jacking point. Model No. YAJ20-40LR also
offers a long reach chassis, ideal for accessing deep set
jacking points.
attaching the handle - yaJ15-30, yaJ20-40, yaJ20-40LR
the pin back through the jack, lining up the handle and
through the other side. Secure with circlips.
air hoses - yaJ15-30, yaJ20-40, yaJ20-40LR
side. The hose marked black or clear into the right-hand side.
(fig.1).
of the handle.
YAJ15-30, YAJ15-30DC, YAJ20-40,
YAJ20-40DC, YAJ20-40LR
yaJ20-40LR
40Tonne 40Tonne
150mm 190mm
409/20 504/20
343/40 416/40
45/75mm 45/75mm
430mm 770mm
1280mm 820mm
1600mm 1770mm
- 2100mm
290mm 282mm
116- 116- 116-
145psi 174psi
10.5cfm 11.5cfm
41kg 33kg 62kg
Issue 2 - 13/03/12