GE Tetra EdgeStrip HO Installation Manual

Tetra EdgeStrip HO
®
LED Lighting System
GEBIH71-2, GEBIH50-2, GEBIH41-2, GEBIH32-2
BEFORE YOU BEGIN
Read these instructions completely and carefully.
RISK OF ELECTRIC SHOCK
∙
Turn power off before inspection, installation or removal.
∙
Properly ground power supply enclosure.
RISK OF FIRE
∙
Use only UL approved wire for input/output connections.
Minimum size 18 AWG (0.82mm
∙
Follow all NEC and local codes.
∙
Not to be submerged or used in a marine environment.
RISK OF FIRE OR ELECTRIC SHOCK
∙
LED Retrofit Kit installation requires knowledge of
sign electrical systems. If not qualified, do not attempt
installation. Contact a qualified electrician.
∙
Install this kit only in host signs that have been identified in
the installation instructions and where the input rating of
the retrofit kit does not exceed the input rating of the sign.
∙
Installation of this LED retrofit kit may involve drilling or
punching of holes into the structure of the sign. Check
for enclosed wiring and components to avoid damage to
wiring and electrical parts.
∙
Do not make or alter any open holes in an enclosure of
wiring or electrical components during kit installation.
Prepare Electrical Wiring
Electrical Requirements
• Limited to use in dry and damp locations. The suitability of rain
enclosures shall be determined if intended for wet location.
• The grounding and bonding of the LED Driver shall be done in
accordance with National Electric Code (NEC) Article 600.
• Follow all National Electric Codes (NEC) and local codes.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
This Class [A] RFLD complies with the Canadian standard ICES-005. Ce DEFR de la classe [A] est conforme à la NMB-005 du Canada.
WARNING / AVERTISSEMENT
RISQUES DE DÉCHARGES ÉLECTRIQUES
∙
Coupez l'alimentation avant l'inspection, l'installation ou le déplacement.
∙
Assurez-vous de correctement mettre à terre l'alimentation électrique.
RISQUES D'INCENDIE
∙
N'utilisez que des fils approuvés par UL pour les entrées/sorties de connexion. Taille
) minimum 18 AWG (0.82mm
2
∙
Respectez tous les codes NEC et codes locaux.
∙
Ne pas submerger ou installer dans un environnement marin.
RISQUE D'INCENDIE OU DE CHOC ÉLECTRIQUE
∙
L'installation de l'équipement de remplacement DEL exige Ia connaissance des
systèmes électriques pour enseignes. Si non qualifié, ne tentez pas d'installation.
Veuillez contacter un électricien qualifié.
∙
Risque d'incendie ou de choc Électrique. Installez cet ensemble seulement dans des
enseignes hôtes qui ont été identifiés dans les instructions d'installation et dont la
capacité d'entrée de l'ensemble ne dépasse pas la capacité d'entrée de l'enseigne.
∙
L'installation de cet équipement de remplacement DEL peut impliquer le perçage
ou le poinçonnage de trous dans la structure du panneau Vérifiez le câblage et
les composants inclus pour éviter d'endommager le câblage et les composants
électriques.
∙
Ne pas faire ou modifier les trous ouverts dans une enceinte de câblage ou de
composants électriques pendant l'installation de cet équipement de remplacement DEL.
)
2
Save These Instructions
Use only in the manner intended by the manufacturer. If
you have any questions, contact the manufacturer.
RETROFIT SIGN CONVERSION LED KIT FOR USE ONLY
IN ACCORDANCE WITH KIT INSTRUCTIONS.
KIT IS COMPLETE ONLY WHEN ALL PARTS REQUIRED
BY THE INSTRUCTIONS ARE PRESENT.
TROUSSE DE CONVERSION À DEL POUR LA
MODERNISATION DES ENSEIGNES
À UTILISER CONFORMÉMENT AU GUIDE D'INSTALLATION.
Installation Guide
SIGN097 | GE2027-2822
24 24
Volt