Siemens LOGO! Installation Specification Sheet

LOGO!
Installation, Connection, Technical specifications
CSM 230 Order number: 6GK7177-1FA10-0AA0
A5E03733191-04
1 1 1
2
L1 N
X10
DC 115...210V 0.02...0.01A
AC 100...240V ~ 0.02...0.01A
s
1
3
X1:P4
AC/DC P1 P2 P3 P4
230V
LOGO! CSM230
6GK7177-1FA10-0AA0
X1:P1 TO X1:P4 FOR LAN ONLY P2
P1 P3
X1:P1 X1:P2 X1:P3
1
52,4
71,5
Status of LEDs
RJ-45 jacks for connections via Ethernet (10/100 Mbps)
1
LED Status Meaning
Three screw terminals:
2
AC/DC Off Power is not connected or the connected
L1 Conductor
230V power is too low.
N Neutral Conductor
AC/DC On Power is connected.
Functional grounding
230V
P1 - P4 Off No connection via Ethernet (link down).
LED for the power supply (AC/DC 230V) and
LEDs for the Ethernet communication status (P1 - P4)
P1 - P4 On The connection via Ethernet is established (link up).
P1 - P4 Flashing LOGO! receives / sends data via Ethernet.
© Siemens AG 2012
Wall mounting
Mounting slides
Hole pattern for wall mounting
Release 06/2012
Product information
All dimensions in mm
Hole for screw Ø 4 mm
Prior to wall-mounting, the mounting slides on the back
Tightening torque 0.8 ... 1.2 Nm
of the device are pushed open.
DIN rail mount RJ-45 jacks with MDI-X assignment
1
L- N
X1:P4
AC/DC
P1 P2 P3 P4
230V
Pin 8 - n. c.
X1:P1 X1:P2 X1:P3 Pin 7 - n. c.
Pin 6 - TD -
Pin 5 - n. c.
Pin 4 - n. c.
Pin 3 - TD +
2
Pin 2 - RD -
Pin 1 - RD +
1. Fit the LOGO! onto the DIN rail.
2. Press down the lower part until the device locks in place.
The mounting slide on the back must snap into place.
Technical specifications
Ethernet interface
Communications connector 4 x RJ‑45 jacks with MDI‑X assignment 10/100 Mbps
36.0
(half / full duplex), autopolarity, autonegotiation
Network cable A standard Ethernet cable can be connected to the Ethernet interface.
However, to minimize electromagnetic interference, Siemens
recommends a shielded Ethernet cable with a twisted pair
(category 5) with a shielded RJ-45 connector at both ends.
Largest data packet 1518 byte
Smallest data packet 64 byte
Delay resulting from latency When a frame passes through the CSM 230, it is delayed
by the store and forward function of the switch:
- with a 64 byte frame length by approx. 8 μs (at 100 Mbps).
- with a 1518 byte frame length by approx. 125 μs (at 100 Mbps).
Topology Star and bus topology
Note that the direct connection of two ports on the switch or
accidental connection over several switches causes an illegal loop.
Such a loop can lead to network overload and network failures.
Insulation of the ports All ports adhere to 1.5 kV insulation voltage:
- to shield
- between the ports.
Learnable MAC addresses 1024
Aging Time 300 seconds
Electrical specification
Input voltage AC 100 ... 240 V
DC 115 ... 210 V
Permitted line power frequency AC 47... 63 Hz
Current consumption (I) - AC 100 ... 240 V: 0.05 ... 0.03 A
- DC 115 ... 210 V: 0.02 ... 0.012 A
Effective power loss 1.8 W
Connection Per terminal for L1 and N
Cable cross section: 1 x 2.5 mm 2 or 2 x 1.5 mm 2
Functional grounding Functional grounding can be established by connecting a cable
from terminal 3, for example to the DIN rail. Such a cable should be
kept as short as possible. Grounding is, however, not necessary for
interference-free operation.
Technical specifications
The product meets the requirements and aims of the following EC directives:
Further technical specifications
EU Directive 2004/108/EC "Electromagnetic Compatibility" (EMC Directive)
Operating temperature - Emission: EN 55022 Class B: 2010
0 ... 55°C
- Immunity: EN 61000-6-2: 2005
Transport/storage temperature - 40°C ... +70°C
EU Directive 2006/95/EC "Low Voltage Directive" (LVD)
- Safety: EN 61131-2: 2008
Relative humidity during operation < 90% (no condensation)
The EC Declaration of Conformity is available for all responsible authorities at:
Dimensions (W x H x D) in mm 72 (4 TE) x 90 x 55 mm
Siemens Aktiengesellschaft
Net weight 155 g Industry Automation, I IA SC CI
Postfach 4848
Installation 35 mm DIN rail (DIN EN 60715 TH35) or wall mounting
D-90026 Nuernberg
Germany
Degree of protection IP 20
You will find the EC Declaration of Conformity for this product on the Internet
at the following address:
Approvals
You will find the currently valid approvals on the type plate.
http://support.automation.siemens.com/WW/view/en/10805878
→ Tab "Entry List"
cULus - UL 508 Listed
Filter settings: Entry type: "Certificates"
- CSA C22.2 Number 142
Certificate Type: "Declaration of Conformity"
C-Tick AS/NZS 2064 Class A
Search items(s): <name of the module>
You can use the device in the following hazardous locations:
cULus Haz.Loc. IND. CONT. EQ., E223122, UL 1604, UL 2279-15
Sources of information and other documentation
FM FM3600 and 3611:
CL. I, Div. 2, Group A, B, C, D, T4
The "SIMATIC NET Industrial Ethernet Network Manual" contains
CL. I, Zone 2, Group IIC, T4, Ta = 55°C
detailed information on the network structure, maximum cable lengths,
cabling technology etc.
Installation
Prior to installation, connecting up and commissioning, read the relevant sections http://support.automation.siemens.com/WW/view/en/27069465
in the LOGO! manual: Entry ID: 27069465
http://support.automation.siemens.com/WW/view/en/50074616
You will find additional information on the Siemens LOGO! Web page:
Entry ID: 50074616
When installing and connecting up, keep to the procedures described in the LOGO! manual.
http://www.siemens.com/logo
To fulfill the requirements according radiated emission EN 55022 Class B, the shield of all
connected LAN cables must be grounded.
Sources of information and other documentation
The "SIMATIC NET Industrial Ethernet Networking Manual" contains detailed information
on the network structure, maximum cable lengths, cabling technology etc.
http://support.automation.siemens.com/WW/view/en/27069465
Entry ID: 27069465
You will find additional information on the Siemens LOGO! web page:
http://www.siemens.com/logo